Router/Version: Dlink-DIR868L rev A
Firmware Version: DD-WRT v3.0-r35244 std (03/05/1
Kernel Version: Linux 4.4.120 #2685 SMP Mon Mar 5 08:03:45 CET 2018 armv7l
Previous: r35034
Mode/Status: AP / working
Reset: no
Issues/Errors: Cant select a Wireless Channel any-more it changed to AUTO after upgrade no options in menu
Posted: Tue Mar 06, 2018 12:59 Post subject: Re: E1500
Router/Version: Buffalo WZR-1750DHP/DHPD Firmware: DD-WRT v3.0-r35244 std (03/05/1 Kernel: Linux 4.4.120 #2685 SMP Mon Mar 5 08:03:45 CET 2018 armv7l Previous: BSr34760 Mode/Status: Working Reset: yes via webGUI Issues/Errors: DNSCrypt kills internet connection and no overclocking support
Errors:- Internet access light on the router loads without any issues as long as i do not use DNSCrypt, if i do use it the Internet access light just won't load and i can't get internet access, so i am guessing that the issue is with the DNSCrypt.
Next error is the no overclocking support anymore only the down clocking is allowed, please bring that back.
jwh7 wrote:
I had assumed it was because the R7000P could use the R8000 firmware, though also odd there is no trailed build from BS, only Kong. But I have neither. The first MB or so of Kong's R7000P vs R8000 only has 4 bytes different: address 0x08-0B.
Anyone tried the BS build, or otherwise know what's up? BS? Kong?
Router/Version: Linksys E1500
Firmware: DD-WRT v3.0-r35244 mega ( 03/05/18 )
Kernel: Linux 3.10.108-dd #17976 Mon Mar 5 14:32:56 CET 2018 mips
Previous: 35034 k3x
Mode/Status: AP
Reset: no
Issues/Errors: Only been 15min; got the laptop wired and Nexus 5X on the wireless. Will update tomorrow. Like the F7D8302 on the last build, running `cat /proc/mtd` from Admin->Commands does not output correctly, something w/ the name field is eftup:
Posted: Tue Mar 06, 2018 15:20 Post subject: Re: E1500
Brimmy wrote:
Router/Version: Buffalo WZR-1750DHP/DHPD Firmware: DD-WRT v3.0-r35244 std (03/05/1 Kernel: Linux 4.4.120 #2685 SMP Mon Mar 5 08:03:45 CET 2018 armv7l Previous: BSr34760 Mode/Status: Working Reset: yes via webGUI Issues/Errors: DNSCrypt kills internet connection and no overclocking support
Errors:- Internet access light on the router loads without any issues as long as i do not use DNSCrypt, if i do use it the Internet access light just won't load and i can't get internet access, so i am guessing that the issue is with the DNSCrypt.
Yes - Have issues with DNSCrypt too in recent builds. I'm running Kongs builds and everything was fine up until 33800. The problems, in my case, started with 33900. I managed to get a good working configuration by switching off 'Encrypt DNS' under Services. DNSCrypt still runs however but WAN access is restored. _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Posted: Tue Mar 06, 2018 17:34 Post subject: Re: E1500
wabe wrote:
Yes - Have issues with DNSCrypt too in recent builds. I'm running Kongs builds and everything was fine up until 33800. The problems, in my case, started with 33900. I managed to get a good working configuration by switching off 'Encrypt DNS' under Services. DNSCrypt still runs however but WAN access is restored.
I had to turn off DNSCrypt too for WAN access but i was of the view that if you disable DNSCrypt that it would not run, and if your own is still running then what is the server that is used and how do you see or change it. My issues started after BS r34760
I have not tried any of Kong's builds as he does not support OCing and my routers are OCed to 1200mhz from the default 800mhz and i do not know what errors may happen and i didn't want to risk it.
Posted: Tue Mar 06, 2018 18:10 Post subject: Re: E1500
Brimmy wrote:
I had to turn off DNSCrypt too for WAN access but i was of the view that if you disable DNSCrypt that it would not run, and if your own is still running then what is the server that is used and how do you see or change it. My issues started after BS r34760
Have not investigated further but you may test by running “ps” from the console and check if DNSCrypt is running. On mine it does. My DNS calls are resolved by OpenDNS which correspond to what I set in “Encrypt dns” before disabling it. _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Posted: Tue Mar 06, 2018 18:18 Post subject: Re: E1500
wabe wrote:
Have not investigated further but you may test by running “ps” from the console and check if DNSCrypt is running. On mine it does. My DNS calls are resolved by OpenDNS which correspond to what I set in “Encrypt dns” before disabling it.
Mine only shows DNSmasq to be running which it is. I do not see any DNSCrypt reference after running the ps command, i did see a bunch of root 0 SW< [bioset] though what the hell is that?
Router/Version: D-Link DIR868L
Firmware: DD-WRT v3.0-r35244 std (03/05/1
Previous: Kong's DD-WRT test build 35030M - 2018/02/19
Kernel: Linux 4.4.120 #2685 SMP Mon Mar 5 08:03:45 CET 2018 armv7l
Mode/Status: Gateway/AP
Reset: Yes
Issues/Errors: I restored my settings from a backup but I am unable to connect to vpn settings from previous build and setup. However I am connected to the internet.
Router: Buffalo WZR-1750DHP
Firmware: buffalo-wzr-1750dhp-webflash.bin (v3.0-r35244 std)
Kernel: Linux 4.4.120 #2685 SMP Mon Mar 5 08:03:45 CET 2018 armv7l
Status: Working
Reset: No
Notes on configuration:
FTP server
DNSMasq
USB v3.0
DHCP reservation
Errors:
1. No overclocking
2. user.info : Authentication fail after each http login
3. On every hour (should not be err): daemon.err process_monitor[]: cyclic NTP Update success
Posted: Wed Mar 07, 2018 3:11 Post subject: Upgrade
Router/Version: Asus N66u
Firmware: 35244
Previous: 35034
Mode/Status: Gateway, DHCP, QoS
Reset: No
Issues/Errors: None, so far. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
I am afraid to install it and can not recover the router.
The E1500 is identical (besides a minor SoC revision; BCM5357 rev B0 vs C0) and both use nv64k firmware. I've been running this build for two days.
Edit: now updated a E2500 (nv60k) too...
Router/Version: Linksys E2500
Firmware: DD-WRT v3.0-r35244 mega ( 03/05/18 )
Kernel: Linux 3.10.108-dd #17976 Mon Mar 5 14:32:56 CET 2018 mips
Previous: 33772 k3x
Mode/Status: Gateway router, inside my LAN [and then, AP]
Reset: no [and then, yes]
Issues/Errors: ok, so after not being able to get the wireless to connect, I reset and setup as an AP. Got wireless to connect, didn't touch any Advanced settings. I think I enabled Bluetooth Coexistence before. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Last edited by jwh7 on Thu Mar 08, 2018 2:00; edited 4 times in total