Joined: 18 Aug 2009 Posts: 597 Location: Antigua/Seattle
Posted: Fri Dec 29, 2017 14:57 Post subject:
I've had it loaded for some time no issues yet WIFI seems OK with Qualcomm devices so far as usual it will take DAYS before any one knows for sure if this one is working properly for everyone.
The odds of that are still pretty slim in my opinion.
My main issue has been the problem with qualcomm devices.
There are so many options and configurations and it takes all of them to be tested. _________________ WRT3200ACM
Posted: Fri Dec 29, 2017 15:02 Post subject: WRT1900ACS V2 updated
I just upgraded my WRT1900ACS V2 to this version through the web interface, keeping settings.
No issues so far. _________________ Linksys WRT1900ACS V2 dd-wrt bs r35034
Netgear R8000 dd-wrt kongac r36440M
Joined: 18 Aug 2009 Posts: 597 Location: Antigua/Seattle
Posted: Fri Dec 29, 2017 15:22 Post subject:
adi-brasov wrote:
is this kernel 4.14.x ?
thanks
DD-WRT
Router Model
Linksys WRT3200ACM
Firmware Version
DD-WRT v3.0-r34311 std (12/29/17)
Kernel Version
Linux 4.9.72 #91 SMP Thu Dec 28 04:11:35 CET 2017 armv7l _________________ WRT3200ACM
Strange I was running I think 34177 I think before this.
I'll download that version and load it and see if it really has the old kernel.
EDIT: OK I have 34178 I'll load it now and post the info.
it could be prepared in those changesets, but may be not activated in a makefile or somewhere.
i think it was only a preparation ...
Here is the info from 34178.
At first glance it looks like the only significant change was the progression of the Kernel version.
So I expect no change on my end as it has been working fine for my purposes.
driver name: mwlwifi
chip type: 88W8964
hw version: 7
driver version: 10.3.4.0-20171129
firmware version: 0x09030202
power table loaded from dts: no
firmware region code: 0x10
mac address: 60:38:e0:13:xx:xx
2g: enable
5g: disable
antenna: 4 4
irq number: 47
ap macid support: 0000ffff
sta macid support: 00010000
macid used: 00000001
radio: enable
iobase0: e1000000
iobase1: e1280000
tx limit: 1024
rx limit: 16384 _________________ WRT3200ACM
Downloaded from the link supplied at beginning of this thread.Updated today via dirty flash from v33986. Had version 33679 on the other partition, from prior dirty flash.
Speeds were not good. Wireless signal was all over the place, dropping in and out, specifically on the 5ghz channel.
Figured I would do a complete refresh and start over to give it fair shake, tried flashing back to Linksys stock FW and bricked the son-of-a-bitch. I could hear Myers in the back of my head as I was pulling the piece of shit apart with a screw driver. I'll make it a point to use his method(s) moving forward. Specifically, the partition trick so I can leave Linksys on the other.
Anyway, I restarted with clean flash through serial cable. On the plus side it motivated me to flash the WDS test build brainslayer put together on 12/12, which is working great at the moment.
Joined: 07 Nov 2008 Posts: 142 Location: Spring Hill, Fl
Posted: Sat Dec 30, 2017 2:45 Post subject:
Has any fellow wrt1900acv1 owner attempted the new firmware yet? Since my wrt32x is going back im leary to pop it on. _________________ modem: arris tm1602
router: r7800 voxel 1.0.2.77sf w/ kamoj 5.3b12 addon
ap: wrt1900ac v1 bs 43136,dir-825 b1 bs41117
NAS: Iomega ix2-200 CE 4tb, Seagate 1tb usb drive
Wash your hands and DONT TOUCH YOUR FACE!!!
Installed r34311 on my WRT1900ACSv1 as a flash upgrade, keeping existing config. Everything seems to be working fine so far. Will post if I have any issues.
________________
Linksys WRT1900ACS v1 - r34311