anybody flash a wrt3200acm, and can confirm 5ghz band works properly? _________________ My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )
Joined: 05 Apr 2017 Posts: 981 Location: Louisiana, USA
Posted: Fri Nov 17, 2017 3:42 Post subject:
I created a separate Thread just for the WRT1900AC v1. In the off chance this doesn't solve the reboot issue - all the information will be in one place to send to Brainslayer.
FIRMWARE:OpenWrt SNAPSHOT r8217-2cc821e / LuCI Master (git-18.276.41146-280dd33) MODEM:ARRIS SURFBoard SB8200 ROUTER:Linksys WRT32X USB NAS:Western Digital BLACK 1 TB Hardrive + Startech USB 3.0 External SATA III Enclosure
anybody flash a wrt3200acm, and can confirm 5ghz band works properly?
No it's not. I have a 100 Mbps connection and I get 10 Mbps on download on 5 Ghz.
Looks like the new Marvell firmware 0x0903bee1 seems to be causing problems.
Back to r33555.
anybody flash a wrt3200acm, and can confirm 5ghz band works properly?
No it's not. I have a 100 Mbps connection and I get 10 Mbps on download on 5 Ghz.
Looks like the new Marvell firmware 0x0903bee1 seems to be causing problems.
Back to r33555.
I used to always select AC only and one of the lower channels on previous builds and it worked fine. The last two builds r33679 and 33772 I've had problems with those setting (both restored and with a fresh install). I've had to "fiddle" with channels and network modes for my PC to connect. However, once it consistently establishes a connection the speeds have been quite good.
Posted: Fri Nov 17, 2017 5:35 Post subject: WRT1900ACS V2
Two hours uptime on my WRT1900ACS V2 so far. Seems stable.
Upgraded through web interface saving all settings. _________________ Linksys WRT1900ACS V2 dd-wrt bs r35034
Netgear R8000 dd-wrt kongac r36440M
Installed r33772 on my WRT1900ACSv1 as a flash upgrade, keeping existing config. Will post if I have any issues. (Ran previous build r33679 for 11days 15hrs without issues)
________________
Linksys WRT1900ACS v1 - r33772
Updated.... restored to factory then restored from backup nvram...
Initial results are promising. Openvpn works.
However, gui slowdown and non responsiveness reared its ugly head again.
The newest SFE patch that allows sfe to work with policy based routing has still not been incorporated. _________________ WRT3200ACM V1 r39267 std (03/22/19) OpenVPN client
anybody flash a wrt3200acm, and can confirm 5ghz band works properly?
No it's not. I have a 100 Mbps connection and I get 10 Mbps on download on 5 Ghz.
Looks like the new Marvell firmware 0x0903bee1 seems to be causing problems.
Back to r33555.
I used to always select AC only and one of the lower channels on previous builds and it worked fine. The last two builds r33679 and 33772 I've had problems with those setting (both restored and with a fresh install). I've had to "fiddle" with channels and network modes for my PC to connect. However, once it consistently establishes a connection the speeds have been quite good.
For me, I found that whenever I have had to play around with the channels etc., to get a connection, it would eventually flake out. I will wait.
tx. _________________ My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )
anybody flash a wrt3200acm, and can confirm 5ghz band works properly?
No it's not. I have a 100 Mbps connection and I get 10 Mbps on download on 5 Ghz.
Looks like the new Marvell firmware 0x0903bee1 seems to be causing problems.
Back to r33555.
Flashed it last night, working like a charm here, getting 100Mbps over 5Ghz (maxing out by broadband connection)
anybody flash a wrt3200acm, and can confirm 5ghz band works properly?
No it's not. I have a 100 Mbps connection and I get 10 Mbps on download on 5 Ghz.
Looks like the new Marvell firmware 0x0903bee1 seems to be causing problems.
Back to r33555.
Flashed it last night, working like a charm here, getting 100Mbps over 5Ghz (maxing out by broadband connection)
I would be very interested in your 5ghz settings as well.
I can't use the 5ghz unless I set the width to 40mhz. When I set it to 80mhz, the ssid disappears. _________________ My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Fri Nov 17, 2017 17:17 Post subject:
Just installed on my wrt3200. Everything looks fine so far. Configured from backup. Updated through the Linksys UI. Don't expect to have issues as I haven't with the last few builds, but you never know. After all it is "beta". _________________ Unifi Security Gateway:Unifi Firmware Netgear r7800:Voxel Firmware Modem:Netgear CM500V voice and Data. ISP:Comcast tutorial for flashing "WRT" series: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813 DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117 Kong DD-WRT Config Tutorial: http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/ I tried to be normal once. Worst 2 minutes ever.