Netgear WNDR3700 V4
DD-WRT v3.0-r33492 std (10/10/17)
Linux 3.18.74 #177 Tue Oct 10 06:58:34 CEST 2017 mips
No Reset
previous r33447
working ok
USB auto mount now works fine
::::::::
Linksys EA8500
DD-WRT v3.0-r33492 std (10/10/17)
Linux 3.18.74 #183 SMP PREEMPT Tue Oct 10 02:54:55 CEST 2017 armv7l
No Reset
previous r33458
It's good
::::::::
Linksys WRT160NL x3
DD-WRT v3.0-r33492 std (10/10/17)
Linux 3.10.107 #40984 Tue Oct 10 05:06:10 CEST 2017 mips
1. No Reset
previous r33413
GUI Install result in flashy power light!!!
TFTP worked fine
From dmesg:
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 194000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000194000-0x0000007d0000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x0000007d0000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0xc22017 .
2. Reset to defaults
previous r33413
GUI Install result in flashy power light!!!
TFTP worked fine
From dmesg:
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 194000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000194000-0x0000007d0000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x0000007d0000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0xc22017 .
3. No Reset
previous r33413
GUI Install worked fine
From dmesg:
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 194000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000194000-0x0000007d0000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x0000007d0000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0x1c2017 .
r33492 seems to run well on the WRT160NL just be warned installing thru GUi might or might not work
'bout all I know
root@Archer-C7:/tmp# write tplink_archer-c7-v2-IL.bin linux
function stop_snmp not found
Image too big for partition: linux
linux: Invalid argument
root@Archer-C7:/tmp#
Nothing.
Last edited by B@R on Tue Oct 10, 2017 21:35; edited 1 time in total
Router: D-Link DIR-859 A3
Firmware DD-WRT v3.0-r33492 std (10/10/17)
Kernel: Linux 3.18.74 #167 Tue Oct 10 06:36:25 CEST 2017 mips
Status: Good
Reset: No
Upgraded from 33413 via web interface GUI
- 2.4Ghz and 5Ghz radios enabled
- QOS enabled
- Port forwarding enabled
- ath0.1 guest interface enabled
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Oct 11, 2017 0:01 Post subject:
other people reported its fixed and your ticket list is insane full of old tickets which are no way reproduceable. see apply over wan etc. i do this every day
and your spiking latencies is maybe a indicator of a broken cable? its just the switch which works indepenend from any os _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Oct 11, 2017 0:07 Post subject:
gin-n-tonic wrote:
Router Model: Netgear WNDR3700v2
GUI upgrade from r33006
Status: good
Reset: none
Errors: OpenVPN server not working - though some quick googling suggests I need to make new certificates.
It's been years since I did that, need to review the procedure...
openvpn server works. check for config changes in latest openvpn versions like the "proto" field in addition some insecure protocols are disabled in openssl like sslv3 etc. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
root@Archer-C7:/tmp# write tplink_archer-c7-v2-IL.bin linux
function stop_snmp not found
Image too big for partition: linux
linux: Invalid argument
root@Archer-C7:/tmp#
Nothing.
will check that
can you post the output of cat /proc/mtd ? _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s