New Build 33215 (BS): 08-25-2017-r33215

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4  Next
Author Message
Whammy
DD-WRT User


Joined: 14 Aug 2007
Posts: 50

PostPosted: Sat Aug 26, 2017 13:46    Post subject: Reply with quote
Router/Version: Netgear WNR3500L
Firmware: DD-WRT v3.0-r33215M mega (08/25/17)
Kernel: Linux 3.10.107 #15794 Fri Aug 25 11:57:59 CEST 2017 mips
Previous: DD-WRT v3.0-r32868 mega (07/27/17)
Mode/Status:
Reset:
Issues/Errors: Failed to flash

Every build after the 7/27 build fails to flash on the device due to the size of the build and the 8MB chip.
Sponsor
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2613
Location: Indy

PostPosted: Sat Aug 26, 2017 15:00    Post subject: Reply with quote
Router/Version: Netgear WNDR4000
Firmware: DD-WRT v3.0-r33215M mega (08/25/17)
Kernel: Linux 3.10.107 #15794 Fri Aug 25 11:57:59 CEST 2017 mips
Previous: 33006
Mode/Status: 2.4GHz CB + 5GHz AP
Reset: No...and I flashed it over wireless cuz...I forgot to switch back to cable 8-|
Issues/Errors: Seems fine; running 30min so far

_________________
# NAT/SFE/CTF: limited speed w/ DD # Repeater issues # DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo #
x64 OPNsense 20.7.4|FT2020.6: EA6900v1.1@1GHz, F7D8302@532|DD 44758: DIR-810L, WNDR4500v2 & 4000@533,
R6300v1, RT-N66U@663, E1500@353, WRT54G{Lv1.1,Sv6}@250
|OpenWRT 19.7.3: RT-ACRH13, R6220, WNDR3700v4
johnnyNobody999
DD-WRT User


Joined: 10 Jan 2014
Posts: 345

PostPosted: Sat Aug 26, 2017 19:01    Post subject: Reply with quote
Linksys E4200
Firmware: dd-wrt.v24-33215_NEWD-2_K3.x_mega-e4200.bin
Kernel: Linux e4200 3.10.107 #15794 Fri Aug 25 11:57:59 CEST 2017 mips DD-WRT
Previous: dd-wrt.v24-33180_NEWD-2_K3.x_mega-e4200.bin
Mode/Status: Working with issues
Reset: yes
Issues/Errors: this router hasn't had time sync with this and 7 earlier firmwares - at one time I could time sync from the CLI but that doesn't work anymore - no time sync == no VPN - otherwise the router works fine so I can't say that it is bricked
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 252

PostPosted: Sat Aug 26, 2017 20:21    Post subject: Reply with quote
Router/Version: RT-AC87U/
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1930 SMP Fri Aug 25 07:57:51 CEST 2017 armv7l
Previous: DD-WRT v3.0-r33006 std (08/03/17)
Mode/Status: Gateway/working
Reset: Yes, before and after
Issues/Errors:

Router/Version: RT-AC66U/A1
Firmware: DD-WRT v3.0-r33215M (08/25/17)
Kernel: Linux 3.10.107 #15778 Fri Aug 25 11:42:58 CEST 2017 mips
Previous: DD-WRT v3.0-r33006 giga (08/03/17)
Mode/Status: Repeater Bridge 5Ghz (AC/N-Mixed)/working
Reset: Yes, before and after
Issues/Errors: No: NTP Client does not set time

Edit: Wireless drops, rolling both back to 33006

_________________
Asus AC87U A1 - DD-WRT v3.0-r43217 std (05/22/20)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r43217 std (05/22/20)
Netgear R6400 V2 - DD-WRT v3.0-r43136 std (05/13/20)
Asus AC66U A1 - DD-WRT v3.0-r43136 giga (05/13/20)
mozuku
DD-WRT Novice


Joined: 06 Oct 2014
Posts: 16

PostPosted: Sun Aug 27, 2017 0:45    Post subject: Reply with quote
Router/Version: Buffalo WZR-600DHP2
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1927 Fri Aug 25 07:38:00 CEST 2017 armv7l
Previous: r33180
Mode/Status: Gateway/AP
Reset: Yes
Issues/Errors: Reboot with openvpn client enabled , wifi does not broadcast.
dino3000
DD-WRT Novice


Joined: 18 Sep 2016
Posts: 2

PostPosted: Sun Aug 27, 2017 1:32    Post subject: New Build 33215 (BS): 08-25-2017-r33215 Reply with quote
Router/Version: Netgear R8000
Firmware: DD-WRT v3.0-r33215
Mode/Status: AP
Reset: Yes
Issues/Errors: Flashing, USB, NAS, Wifi

Can't flash this version with the browser. It stays in 'upgrading firmware'. After 10 minutes powecycled the router. Router booted up with the previous version (r33006) with the default settings.
Reverted to the factory firmware, then flashed the factory to ddwrt version of r33215. That worked, but found the following issue's:

- USB support is not stable. When USB support is turned on the first time, it recognizes the USB sticks. But after a reboot it doesn't.
It only works if USB support is turned off and then apply settings and turned on again and apply settings.

- The NAS share's doesn't show up the windows network neighbourhood (It does in r33006).

- Wifi is on, but no signal.

Reverted to r33006.
O-DuB
DD-WRT Novice


Joined: 23 Aug 2017
Posts: 8
Location: Ohio, USA

PostPosted: Sun Aug 27, 2017 1:35    Post subject: Reply with quote
Code:
Router/Version: Asus RT-N66U
Firmware: DD-WRT v3.0-r33215M big (08/25/17) (what's up with the M?)
Kernel: Linux 3.10.107 #15790 Fri Aug 25 11:54:07 CEST 2017 mips
Previous: 33006 big
Mode/Status: working on 2 identical units
Reset: no
Issues/Errors: none

_________________
"Opportunity is often missed by most people because it is dressed in overalls, and looks like work."
Brimmy
DD-WRT User


Joined: 29 Mar 2015
Posts: 381

PostPosted: Sun Aug 27, 2017 2:54    Post subject: Reply with quote
Router/Version: Buffalo WZR-1750DHP
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1923 SMP Thu Aug 24 21:09:13 CEST 2017 armv7l
Previous: 33006
Mode/Status: Working
Reset: yes via web GUI reset to defaults
Issues/Errors: none so far
Uptime: 7mins.

Saw this under CPU....undefined EDSP, what is EDSP and why is it undefined.
slobodan
DD-WRT Guru


Joined: 03 Nov 2011
Posts: 1551
Location: Zwolle

PostPosted: Sun Aug 27, 2017 6:02    Post subject: Reply with quote
johnnyNobody999 wrote:
router hasn't had time sync with this and 7 earlier firmwares - at one time I could time sync from the CLI but that doesn't work anymore - no time sync == no VPN - otherwise the router works fine so I can't say that it is bricked[/b]

I have onehundredninetythree.sixtyseven.seventynine.twohundredandtwo as NTP IP and it works perfectly with time sync.

_________________
2 times RT-AC56U running 33772 with entware-ng, Yamon 3 (SFE disabled).

Asus RT-N16 running Merlin LTS fork RT-N16_3.0.0.4_374.43_2-25E8j9527.trx with entware-ng.

2 times Asus RT-N16 running dd-wrt.v24-33772_NEWD-2_K3.x_big.bin with entware-ng

E4200 V1 running dd-wrt.v24-33772_NEWD-2_K3.x_mega-e3000.bin

3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running dd-wrt.v24-33772_NEWD-2_K3.x_mega-e3000.bin (bridged with LAN cable)

redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11476
Location: Wherever the wind blows- North America

PostPosted: Sun Aug 27, 2017 11:47    Post subject: Reply with quote
Whammy wrote:
No it doesn't. The WNR3500L fails to flash.


That's probably true...I don't have a WNR3500L unit but the Netgear units typically (from past experience) use more flash...one section for the CFE...and another (hidden/protected) for MAC address and I believe it was radio settings in another section of the flash. This causes the amount of usable flash for firmware to be lessened.

Just because it fits on one unit...doesn't mean it will work on every unit due to how the manufacture sets up CFE area and other hidden areas of the flash.

redhawk

_________________
I do NOT provide personal assistance through chat or phone....so please don't ask.
wicket
DD-WRT Novice


Joined: 18 Jul 2017
Posts: 41
Location: Wisconsin, USA

PostPosted: Sun Aug 27, 2017 14:19    Post subject: Update Reply with quote
Router/Version: Linksys EA 6500v1
Firmware: DD-WRT v3.0-r33215M giga (08/25/17)
Kernel: Linux 3.10.107 #15778 Fri Aug 25 11:42:58 CEST 2017 mips
Previous: DD-WRT v3.0-r33006 giga (08/03/17)
Mode/Status: Gateway/AP
Reset: No

Issues/Errors: Wireless Drops seems to happen about twice
a day router says its broadcasting but no device can see or connect, also Ipv6 address seems to come and go. Can force address by going to the IPv6 page hitting save and apply settings this will issue an ip but a little while later its like the router forgets it and releases it without attempting to obtain a new one. Unless I go back and repeat the above step.

Reverting back to DD-WRT v3.0-r33006 giga (08/03/17)
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11476
Location: Wherever the wind blows- North America

PostPosted: Sun Aug 27, 2017 18:15    Post subject: Reply with quote
slobodan wrote:

I have onehundredninetythree.sixtyseven.seventynine.twohundredandtwo as NTP IP and it works perfectly with time sync.


It didn't work for me when in CB mode. I still have to manually set the date/time. I wonder how Kong fixed his builds for NTP time. His second (fixed) build of 33010 has the NTP time working now.

redhawk

_________________
I do NOT provide personal assistance through chat or phone....so please don't ask.
kbrabble
DD-WRT Novice


Joined: 29 Jul 2017
Posts: 2

PostPosted: Sun Aug 27, 2017 18:19    Post subject: Reply with quote
Router/Version: Trendnet TEW828DRU
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1927 Fri Aug 25 07:38:00 CEST 2017 armv7l
Previous: DD-WRT v3.0-r33006 std (08/03/17)
Mode/Status: Gateway/AP
Reset: Yes

Issues/Errors: Router stable for ~15 mins then reboots, after which router reboots every couple of minutes. This behavior only happens when my other routers configured as client or repeater bridges are connected. Without client/repeater bridges router remains stable longer, but still requires a couple of reboots a day. Reverted to 33006.

Router/Version: Trendnet TEW828DRU
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1927 Fri Aug 25 07:38:00 CEST 2017 armv7l
Previous: DD-WRT v3.0-r33006 std (08/03/17)
Mode/Status: Client Bridge
Reset: Yes

Issues/Errors: Router exhibited the same behavior when configured as a Gateway/AP as the other router. When configures as a Client Bridge all functions appear to work properly, however it exhibits the same instability in which a reboot is required a couple of times a day to regain connectivity. NTP not updating. Reverted to 33006.

Router/Version: Trendnet TEW818DRU
Firmware: DD-WRT v3.0-r33215 std (08/25/17)
Kernel: Linux 4.4.83 #1927 Fri Aug 25 07:38:00 CEST 2017 armv7l
Previous: DD-WRT v3.0-r33006 std (08/03/17)
Mode/Status: Client Bridge/OpenVPN Client
Reset: Yes

Issues/Errors: After ~24 hours up time processor usage is at 84%, every thing was still functioning properly and the router was not overly hot. A reboot brought the processor usage back down to its normal 4% range. Will continue to monitor and downgrade if the issue persists. NTP not updating.
cdkiller
DD-WRT User


Joined: 26 Jun 2007
Posts: 262
Location: Trinidad & Tobago

PostPosted: Sun Aug 27, 2017 19:13    Post subject: wget no work with https urls Reply with quote
Router Model: Buffalo WZR-600DHP2
Firmware Version: DD-WRT v3.0-r33215 std (08/25/17)
Kernel Version: Linux 4.4.83 #1927 Fri Aug 25 07:38:00 CEST 2017 armv7l

Issues/Errors: wget does not work with https urls. If an https url is used this error is output: "wget: not an http or ftp url: https://rest_of_url".

Without going into the details, the reason I need wget to work with https urls is to wget an API url to send my IP address to Smart DNS type service. I feel as though this used to work in previous versions of dd-wrt, not sure when it stopped working.

_________________
[everything is to be replicate]
Crescentis
DD-WRT Novice


Joined: 28 Aug 2017
Posts: 3

PostPosted: Mon Aug 28, 2017 3:56    Post subject: Reply with quote
Router/Version: E4200v1
Firmware: dd-wrt.v24-33215_NEWD-2_K3.x_mega
Kernel: 3.0
Previous: 30826 3.0
Mode/Status: Working, with issues
Reset: 30/30/30
Issues/Errors: OpenVPN client not working

Working:
VAP
VLANs
QOS
Keep-alive

Not working:
OpenVPN - not working even with the special instructions posted by jwh7:

"3. (egc) [from prior builds] "OpenVPN 2.4 is stable but you have to tweak your configuration files notably:"
mtu-disc yes
proto udp4"

I placed the following to commands in the additional config for OpenVPN client, and it still doesn't work:

mtu-disc yes
proto udp4
Goto page Previous  1, 2, 3, 4  Next Display posts from previous:    Page 2 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum