New BS build r33006 8-03-2017

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next
Author Message
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Tue Aug 15, 2017 18:40    Post subject: Reply with quote
vit5421 wrote:
The last free version is InSSIDer 40020. Attached and just replace extension to msi. You can google it as well for this version.


I assume this is a .exe file when I looked at it. When I changed the extension I got a message about not running on the version of windows I have, which is windows 10 pro.

Not sure why I would mess with this when I can get a "new" free app that does work.
Go to
https://www.acrylicwifi.com/en/wlan-software/wlan-scanner-acrylic-wifi-free/download-wifi-scanner-windows/
This is free and current.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
Sponsor
vit5421
DD-WRT User


Joined: 12 Nov 2015
Posts: 423

PostPosted: Tue Aug 15, 2017 18:44    Post subject: Reply with quote
Dear Bill,
If you will change the extension to msi as my instruction it will work just fine. I like and trust InSSIDer but may be Acrylic will be good too
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Tue Aug 15, 2017 19:41    Post subject: Reply with quote
vit5421 wrote:
Dear Bill,
If you will change the extension to msi as my instruction it will work just fine. I like and trust InSSIDer but may be Acrylic will be good too


Yup, with the msi extension it works fine. I used InSSIDer for a number of years in my job. Retired now.
Thanks.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Tue Aug 15, 2017 21:47    Post subject: Reply with quote
I just lost wireless for a sec and it came back
Then saw this in the logs:

Code:
Aug 15 20:34:23 DD-WRT user.err : Caught SIGSEGV (11) in EVP_VerifyFinal
Aug 15 20:34:23 DD-WRT user.err : Fault at memory location 0x00000057 due to address not mapped to object (1).
Aug 15 20:34:23 DD-WRT user.err : Thread 28394: httpd
Aug 15 20:34:23 DD-WRT user.err : === Context:
Aug 15 20:34:23 DD-WRT user.err : TRAPNO:0000000e ERRCODE:00000017 OLDMASK:00000000 R0:009d3cb0
Aug 15 20:34:23 DD-WRT user.err : R1:0000000a R2:b6f00f90 R3:00000003 R4:009d3cb0
Aug 15 20:34:23 DD-WRT user.err : R9:beefcaa4 R10:009df340 FP:00000000 IP:0010bf00
Aug 15 20:34:23 DD-WRT user.err : SP:b6ccfc10 LR:b6e7c248 PC:b6e7bb68 CPSR:20000010
Aug 15 20:34:23 DD-WRT user.err : FAULTADDR:00000057
Aug 15 20:34:23 DD-WRT user.err : === Backtrace:
Aug 15 20:34:23 DD-WRT user.err : # Searching frame 0 (FP=0x00000000, PC=0xb6e7bb68)
Aug 15 20:34:23 DD-WRT user.err : # PC-49c[0xb6e7b6cc]: 0xe92d4ff0 stmfd sp!
Aug 15 20:34:23 DD-WRT user.err : # Stack at 0x00000000 is not mapped; terminating backtrace.
Aug 15 20:34:23 DD-WRT user.err : /usr/lib/libcrypto.so.1.0.0[0xb6dde000](EVP_VerifyFinal+0x000001ac)[0xb6e7bb68]
Aug 15 20:34:23 DD-WRT user.err : === Code:
Aug 15 20:34:23 DD-WRT user.err : b6e7bb28: eaffffb5 e5904028 e3540000 1afffff2 e58d4000 e1a03004 e3a02069 e3a0106c
Aug 15 20:34:23 DD-WRT user.err : b6e7bb48: e3a00006 ebffe7b9 eaffffab e590300c e92d4010 e1a04000 e3530000 0a000005
Aug 15 20:34:23 DD-WRT user.err : b6e7bb68: >e5933054 e3530000 0a000002 e12fff33 e3a03000 e5843014 e5940010 e3500000
Aug 15 20:34:23 DD-WRT user.err : b6e7bb88: 08bd8010 ebffab1f e3a03000 e5843010 e8bd8010 e92d40f0 e2504000 e24dd014


Any ideas?
doniNZ74
DD-WRT User


Joined: 27 Apr 2016
Posts: 94
Location: Down down .... under

PostPosted: Wed Aug 16, 2017 2:49    Post subject: Reply with quote
11 days of uptime now for me Very Happy Very Happy Very Happy
_________________
Linksys WRT1900ACv2 - My go to build: DD-WRT v3.0-r39800 std (05/15/19) - STABLE Smile
Dunkelstar
DD-WRT Novice


Joined: 18 May 2017
Posts: 19

PostPosted: Fri Aug 18, 2017 18:08    Post subject: Reply with quote
doniNZ74 wrote:
11 days of uptime now for me Very Happy Very Happy Very Happy


15 days with no issues for the WRT3200 as of this afternoon running r33006.
canmanxl
DD-WRT Novice


Joined: 02 Feb 2017
Posts: 35

PostPosted: Fri Aug 18, 2017 20:14    Post subject: 2.4GHz radio Reply with quote
The only issue I have had with this build is my 2.4GHz radio drops out ever so often. I will see it disappear on my phone then come back up shortly after. But haven't had any random reboots.
aventus
DD-WRT User


Joined: 02 May 2014
Posts: 60

PostPosted: Fri Aug 18, 2017 21:28    Post subject: Reply with quote
@canmanx
Which router?
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Fri Aug 18, 2017 21:42    Post subject: Reply with quote
aventus wrote:
@canmanx
Which router?

YES Wink
Please put router model in text of message, or better yet, in your sig. Really helps others to know what router you are having good luck with or bad luck.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
canmanxl
DD-WRT Novice


Joined: 02 Feb 2017
Posts: 35

PostPosted: Fri Aug 18, 2017 23:20    Post subject: Reply with quote
aventus wrote:
@canmanx
Which router?


Sorry guys!

I have a 1900acs v1.
elvisimprsntr
DD-WRT User


Joined: 15 Nov 2008
Posts: 149

PostPosted: Sat Aug 19, 2017 6:52    Post subject: Reply with quote
elvisimprsntr wrote:
BACKGROUND

I want to thank everyone who suggested using LEDE. Its lightweight, fast, reliable, and works on all three Linksys WRT routers I have (ACv1, ACSv1, ACM). I am running the generic builds on all three. http://downloads.lede-project.org/releases/17.01.2/targets/mvebu/generic/

While LEDE does not have a lot of features DD-WRT has out of the box, I do not use or need them. In March, moved to a separate appliance from http://protectli.com running open source enterprise class firewall software from http://www.pfsense.org to allow me to easily add a Netgear LB1120 LTE Modem for dual WAN failover. I tried a number of off-the-shelf dual WAN failover routers (Cisco, Linksys), none of which offered the features I needed to restrict which LAN IP had access to the LTE failover WAN. Higher end enterprise class firewalls which may have offered those features were not cost effective for my needs. I could not be more pleased with pfSense, Protectli, and Netgear LTE modems.

NETWORK CONFIG

FW1: pfSense, Dual WAN failover, DHCP, Static Leases, IPSec VPN, OpenDNS servers, DyDNS
    WAN1: Crapcast -> Soon to be ATT Fiber
    WAN2: ATT IoT LTE 1GB/yr for $25

AP1: WRT1900ACSv1:AP mode, wired to FW1, firewall and DHCP disabled
AP2: WRT1900ACv1: xfinitywifi WWAN Client Bridge guest access, firewall, NAT, DHCP
AP3: WRT3200ACM: AP mode, wired to AP1, firewall and DHCP disabled, testing before placing into service

EASY WAY TO FLASH LEDE

The easiest way I found to flash LEDE is to download the LEDE factory image, then use the TTL Serial Console to flash via TFTP. Just remember to perform a factory reset after flashing LEDE to wipe out any config remnants from previous firmware. This eliminates the need to flash back to Linksys factory firmware just to re-flash LEDE, and you can flash over both partitions at the same time. Instructions: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1054186#1054186

The added bonus is LEDE drops into a Linux prompt over the TTL Serial Console so you can change the IP address to access the LuCI interface while still wired to you existing network. Example: ifconfig br-lan 192.168.69.200 netmask 255.255.255.0. The TTL Serial Console will also echo console log output so you can monitor what LEDE is doing.

If you need a Linksys WRT Series TTL Console Port Adapter, I still have a few left out of the 100 I had made in China for everyone. http://www.ebay.com/itm/132070173439 Demand does not seem to be that high, so I am not sure if I will have more made.

SUMMARY

DD-WRT seems to be getting bloated as it tries to do everything, for all routers in existence, and mostly by one or two developers (BS and Kong). And since Kong has stopped supporting the WRT Series, the quality of the DD-WRT builds for them seems to be on the decline. LEDE seems focused on doing a very limited number of things very well, but allows one to add additional packages to suit your specific needs.

After 10+ faithful years of running DD-WRT on my various routers over the years, I just might never switch back to DD-WRT. This may very well be my last post on DD-WRT, but I am sure you will be able to find me on the LEDE or OpenWRT forums.

Cheers!

Elvis


UPDATE

After nearly a week of testing LEDE on ACM, I have pressed it into service. The ACM is now my primary router. I run LEDE (Kernel 4.4) on ALL three routers.

AP1: WRT3200ACM: AP mode, wired to FW1, firewall and DHCP disabled
AP2: WRT1900ACSv1: AP mode, wired to AP1, firewall and DHCP disabled, backup
AP3: WRT1900ACv1: xfinitywifi WWAN Client Bridge guest access, firewall, NAT, DHCP

_________________
http://www.youtube.com/user/TheElvisImprsntr/
zabolots
DD-WRT User


Joined: 02 Dec 2015
Posts: 91

PostPosted: Sat Aug 19, 2017 13:14    Post subject: Reply with quote
elvisimprsntr wrote:
I run LEDE (Kernel 4.4) on ALL three routers.

AP1: WRT3200ACM: AP mode, wired to FW1, firewall and DHCP disabled
AP2: WRT1900ACSv1: AP mode, wired to AP1, firewall and DHCP disabled, backup
AP3: WRT1900ACv1: xfinitywifi WWAN Client Bridge guest access, firewall, NAT, DHCP


Just curious, but are you doing your own builds? If not, where are you finding LEDE builds for devices other than the WRT1900ACv1 that are based on the 4.4 kernel (which I know DavidC does over on the LEDE forums due to the crashing issue with >4.4 kernels)?
elvisimprsntr
DD-WRT User


Joined: 15 Nov 2008
Posts: 149

PostPosted: Sat Aug 19, 2017 14:42    Post subject: Reply with quote
zabolots wrote:
elvisimprsntr wrote:
I run LEDE (Kernel 4.4) on ALL three routers.

AP1: WRT3200ACM: AP mode, wired to FW1, firewall and DHCP disabled
AP2: WRT1900ACSv1: AP mode, wired to AP1, firewall and DHCP disabled, backup
AP3: WRT1900ACv1: xfinitywifi WWAN Client Bridge guest access, firewall, NAT, DHCP


Just curious, but are you doing your own builds? If not, where are you finding LEDE builds for devices other than the WRT1900ACv1 that are based on the 4.4 kernel (which I know DavidC does over on the LEDE forums due to the crashing issue with >4.4 kernels)?


I am running the generic builds http://downloads.lede-project.org/releases/17.01.2/targets/mvebu/generic/ which are Kernel 4.4.71 according to the manifest and confirmed via LuCI Status page
Code:
Kernel Version   4.4.71

_________________
http://www.youtube.com/user/TheElvisImprsntr/
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Sat Aug 19, 2017 15:13    Post subject: Reply with quote
elvisimprsntr wrote:
zabolots wrote:
elvisimprsntr wrote:
I run LEDE (Kernel 4.4) on ALL three routers.

AP1: WRT3200ACM: AP mode, wired to FW1, firewall and DHCP disabled
AP2: WRT1900ACSv1: AP mode, wired to AP1, firewall and DHCP disabled, backup
AP3: WRT1900ACv1: xfinitywifi WWAN Client Bridge guest access, firewall, NAT, DHCP


Just curious, but are you doing your own builds? If not, where are you finding LEDE builds for devices other than the WRT1900ACv1 that are based on the 4.4 kernel (which I know DavidC does over on the LEDE forums due to the crashing issue with >4.4 kernels)?


I am running the generic builds http://downloads.lede-project.org/releases/17.01.2/targets/mvebu/generic/ which are Kernel 4.4.71 according to the manifest and confirmed via LuCI Status page
Code:
Kernel Version   4.4.71


I am running davidc502 LEDE. His has latest wireless drivers and kernel. Runs well for me and is more up to date. He provides a 4.4 kernel for the wrt1900ac v1 again with latest drivers.
I am guessing you are aware of his builds, but if not here is link.
https://davidc502sis.dynamic-dns.net/
This site also has a link to his Openwrt support thread.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
elvisimprsntr
DD-WRT User


Joined: 15 Nov 2008
Posts: 149

PostPosted: Sun Aug 20, 2017 16:55    Post subject: Reply with quote
myersw wrote:


I am running davidc502 LEDE. His has latest wireless drivers and kernel. Runs well for me and is more up to date. He provides a 4.4 kernel for the wrt1900ac v1 again with latest drivers.
I am guessing you are aware of his builds, but if not here is link.
https://davidc502sis.dynamic-dns.net/
This site also has a link to his Openwrt support thread.


The problem with the LEDE builds from https://davidc502sis.dynamic-dns.net/
is the root certificate is not trusted and macOS High Sierra Safari will not allow you to accept the untrusted cert.

_________________
http://www.youtube.com/user/TheElvisImprsntr/
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next Display posts from previous:    Page 7 of 8
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum