New BS build r33006 8-03-2017

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next
Author Message
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sat Aug 12, 2017 20:41    Post subject: Reply with quote
Hi all new here
I just bought a WRT 1900 ACS v2.
Flashed latest build from here and had wireless issues where it keep dropping out every 5 - 10 mins.
Not had issue on stock firmware.

Any known issues?
Should I try LDE?
Sponsor
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Sat Aug 12, 2017 21:03    Post subject: Reply with quote
nekromantik wrote:
Hi all new here
I just bought a WRT 1900 ACS v2.
Flashed latest build from here and had wireless issues where it keep dropping out every 5 - 10 mins.
Not had issue on stock firmware.

Any known issues?
Should I try LDE?


You did not state the version you installed. If from database then it is very old.

You can get the latest at this link.
ftp://ftp.dd-wrt.com/betas/2017/

Also read the info in the thread referenced in my sig. Has lots of good info for first timers, especially entry 2.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sat Aug 12, 2017 21:12    Post subject: Reply with quote
myersw wrote:
nekromantik wrote:
Hi all new here
I just bought a WRT 1900 ACS v2.
Flashed latest build from here and had wireless issues where it keep dropping out every 5 - 10 mins.
Not had issue on stock firmware.

Any known issues?
Should I try LDE?


You did not state the version you installed. If from database then it is very old.

You can get the latest at this link.
ftp://ftp.dd-wrt.com/betas/2017/

Also read the info in the thread referenced in my sig. Has lots of good info for first timers, especially entry 2.


I installed r33006
slimbrick87
DD-WRT User


Joined: 10 Jul 2017
Posts: 92

PostPosted: Sat Aug 12, 2017 22:05    Post subject: Reply with quote
nekromantik wrote:
myersw wrote:
nekromantik wrote:
Hi all new here
I just bought a WRT 1900 ACS v2.
Flashed latest build from here and had wireless issues where it keep dropping out every 5 - 10 mins.
Not had issue on stock firmware.

Any known issues?
Should I try LDE?


You did not state the version you installed. If from database then it is very old.

You can get the latest at this link.
ftp://ftp.dd-wrt.com/betas/2017/

Also read the info in the thread referenced in my sig. Has lots of good info for first timers, especially entry 2.


I installed r33006


r33006 works extremely well on my Linksys WRT1900ACS V2. I've had no problems with dropouts.
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sat Aug 12, 2017 22:10    Post subject: Reply with quote
slimbrick87 wrote:
nekromantik wrote:
myersw wrote:
nekromantik wrote:
Hi all new here
I just bought a WRT 1900 ACS v2.
Flashed latest build from here and had wireless issues where it keep dropping out every 5 - 10 mins.
Not had issue on stock firmware.

Any known issues?
Should I try LDE?


You did not state the version you installed. If from database then it is very old.

You can get the latest at this link.
ftp://ftp.dd-wrt.com/betas/2017/

Also read the info in the thread referenced in my sig. Has lots of good info for first timers, especially entry 2.


I installed r33006


r33006 works extremely well on my Linksys WRT1900ACS V2. I've had no problems with dropouts.


On the 5ghz channel?
My settings were:

80hz width
auto channel
mode: ac+n
WPA2 AES
Fr3DBr
DD-WRT User


Joined: 29 Oct 2009
Posts: 65

PostPosted: Sun Aug 13, 2017 0:32    Post subject: Reply with quote
I'm using the Stock Firmware, for about 3 months without a single issue in my WRT3200ACM, with both 2.4 and 5ghz channels working fine. Smile
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1609
Location: SE Michigan USA

PostPosted: Sun Aug 13, 2017 0:48    Post subject: Reply with quote
@nekromantik
Some folks report better luck when the set a channel rather then leaving it set to auto. Would suggest 36 or better yet 149. I also leave it set to mixed for mode. Everything connects at max speeds for me with it left to the default of mixed. With these settings r33006 ran well for me.

_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sun Aug 13, 2017 11:09    Post subject: Reply with quote
myersw wrote:
@nekromantik
Some folks report better luck when the set a channel rather then leaving it set to auto. Would suggest 36 or better yet 149. I also leave it set to mixed for mode. Everything connects at max speeds for me with it left to the default of mixed. With these settings r33006 ran well for me.


will try that thanks.
you no longer got 1900acs?
Shame Kong stopped builds as people said good things.
I tried LEDE but could not get WAN to work.
nixy82
DD-WRT Novice


Joined: 21 Jul 2014
Posts: 3

PostPosted: Sun Aug 13, 2017 11:44    Post subject: Reply with quote
Hi

I have a 1900ACS v2, I ended up using Kong 31100M it works fine.

I've attached the image file you can use this to flash via the DD-WRT menu (worked for me anyway)

I used 2017_0108_ddwrt-linksys-wrt1900acs.bin

from here :

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1075856#1075856

Attached to post

I've also got pixelserv-tls working on mine if you're interested?
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sun Aug 13, 2017 12:00    Post subject: Reply with quote
nixy82 wrote:
Hi

I have a 1900ACS v2, I ended up using Kong 31100M it works fine.

I've attached the image file you can use this to flash via the DD-WRT menu (worked for me anyway)

I used 2017_0108_ddwrt-linksys-wrt1900acs.bin

from here :

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1075856#1075856

Attached to post

I've also got pixelserv-tls working on mine if you're interested?


As its no longer developed I dont think I wanna use it to be fair. Thanks anyway.
zabolots
DD-WRT User


Joined: 02 Dec 2015
Posts: 91

PostPosted: Sun Aug 13, 2017 12:41    Post subject: Reply with quote
[quote="vit5421"]
elvisimprsntr wrote:

Two months ago I get rid of all my WRT units and get two Netgear r7800 with Kong build. (I am not using VPN and NAS functions).
Looks like Kong is working very hard now with r7800 and its really amazing how Qualcomm-Atheros can be miles ahead of Marvel.


Good to hear. I also got fed up with the constant work required trying to find a stable/fast/reliable build for my WRT1900ACv1. I finally settled on DavidC's custom LEDE build with the 4.4 kernel which is good but still requires a lot of maintenance to keep current.

I have a Netgear r7800 sitting on my desk waiting to be set up with Kong's build and I sure hope it's better than the disappointing Marvell/WRT series has been for me.
elvisimprsntr
DD-WRT User


Joined: 15 Nov 2008
Posts: 149

PostPosted: Sun Aug 13, 2017 12:57    Post subject: Reply with quote
zabolots wrote:
vit5421 wrote:

Two months ago I get rid of all my WRT units and get two Netgear r7800 with Kong build. (I am not using VPN and NAS functions).
Looks like Kong is working very hard now with r7800 and its really amazing how Qualcomm-Atheros can be miles ahead of Marvel.


Good to hear. I also got fed up with the constant work required trying to find a stable/fast/reliable build for my WRT1900ACv1. I finally settled on DavidC's custom LEDE build with the 4.4 kernel which is good but still requires a lot of maintenance to keep current.

I have a Netgear r7800 sitting on my desk waiting to be set up with Kong's build and I sure hope it's better than the disappointing Marvell/WRT series has been for me.


I think @vit5421 wrote that. I fixed it for you.

_________________
http://www.youtube.com/user/TheElvisImprsntr/
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sun Aug 13, 2017 14:00    Post subject: Reply with quote
wish i saw this forum before buying 1900acs.
might swap it for netgear r7000p
vit5421
DD-WRT User


Joined: 12 Nov 2015
Posts: 423

PostPosted: Sun Aug 13, 2017 15:48    Post subject: Reply with quote
If you will stay with Linksys WRT units you will always try to do something to improve it like different builds, Lede, OEM, settings, switching partitions and so on. But its like "Tilting at windmills" coz you will not able to fix a nature of Marvel problems.
Please try r7800 Kong based and hope you will be more happy with proper configuration
nekromantik
DD-WRT Novice


Joined: 12 Aug 2017
Posts: 28

PostPosted: Sun Aug 13, 2017 16:05    Post subject: Reply with quote
vit5421 wrote:
If you will stay with Linksys WRT units you will always try to do something to improve it like different builds, Lede, OEM, settings, switching partitions and so on. But its like "Tilting at windmills" coz you will not able to fix a nature of Marvel problems.
Please try r7800 Kong based and hope you will be more happy with proper configuration


I did not pay full price for 1900acs and cant get same deal on R7800 so only netgear I can get is r7000p
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next Display posts from previous:    Page 5 of 8
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum