Your reports for Broadcom units are greatly appreciated !
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230 OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399 OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795 Install guide R7800:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
The same GUI lock-up issue is observed when the SFE option is turned on via GUI although the router's SSH and WAN connections are still fine.
After the httpd service is restarted, everything is still ok after 50 min uptime. It looks like BrainSlayer indeed has found the SFE lock-up's root cause on the previous version. _________________ Buffalo WZR-1750DHP
I updated this morning to the new release. However two mornings in a row I came in and my upstream bandwidth with my IP is 20mbps, however dslreports and speettest report 300k. I have had to power off then on my router to get my upstream back. This was with SFE off and qos on. I will keep you updated with this build. _________________ Please Fix The Following Bugs:
EOIP Settings not applied automatically after FW upgrade or reboot. http://svn.dd-wrt.com/ticket/4061
The port 80 forwarding bug with out reapplying settings appears to have been fixxed.
Router: Netgear R8500
Firmware: DD-WRT v3.0-r32780M kongac (07/21/17)
Kernel: Linux 4.4.77 #375 SMP Fri Jul 21 12:02:04 CEST 2017 armv7l
Status: Working (with problems)
CPU Temperature: CPU 46.9 °C / WL0 51.0 °C / WL1 45.6 °C / WL2 49.3 °C
Reset: Yes/No (tried both)
Errors: Web interface hangs, SFE problems with OpenVPN - explained below.
Functions enabled: DNSMasq (hosts), USB, NAS/samba, OpenVPN client with policy based routing.
Problems: Web interfaces locks up a lot in r32735M and r32780M both. Firmware upgrade button causes lockup in Chromium; Firefox/Edge work. When SFE is enabled, VPN/PBR (OpenVPN) does not work. All the systems not specified in PBR, and hence unaffected by VPN, functional normally. On at least two occasions the router has locked up upon reboot.
I set SFE on for testing even though I could reach my max wan 200/200 without it. No lockups on this build so far. _________________
Netgear R7800 kongpro 19.07 20190919 || Netgear R7000 36070M kongac (Client Bridge=5GHz, AP=2.4GHz with bridged VAP)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
FYI, in my build qos is enabled even if sfe is turned on I have 3 x A+ on dsl reports with sfe + qos and I do not need download limit.
@Kong, SFE interferes/breaks vlan setup between Router (R7000) & AP (R6300v2).
- Device behind VLAN3 through the trunk port on R6300v2 AP to R7000 lost internet connectivity.
- The same VLAN3 device is successfully getting assigned a VLAN3 IP address, so only the WAN (or NAT?) access is affected.