New build: DD-WRT v3.0 --- 31899 --- 2017/04/24

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2  Next
Author Message
Handyone
DD-WRT User


Joined: 18 Sep 2014
Posts: 154

PostPosted: Mon Apr 24, 2017 14:28    Post subject: New build: DD-WRT v3.0 --- 31899 --- 2017/04/24 Reply with quote
DD-WRT build 31899 - 2017/04/24 has been released: ftp://ftp.dd-wrt.com/betas/2017/04-24-2017-r31899/

Changelog
https://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467
http://svn.dd-wrt.com/timeline

Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29621_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Sponsor
techpro2004
DD-WRT Novice


Joined: 08 Jul 2016
Posts: 33

PostPosted: Mon Apr 24, 2017 15:55    Post subject: Reply with quote
update failed on rt-ac88u. It just shows the old build number/date on the top right corner of the web ui.
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 413

PostPosted: Mon Apr 24, 2017 19:42    Post subject: Reply with quote
Build 31899 previous build 30949

Router: RT-AC87U - primary router/gateway
Firmware Version: DD-WRT v3.0-r31899 std (04/24/17)
Kernel Version: Linux 4.4.63 #1434 SMP Mon Apr 24 08:28:48 CEST 2017 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: 2.4Ghz OK – 5Ghz NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless client’s output table
5Ghz

Router: RT-AC68R - primary router/gateway
Firmware Version: DD-WRT v3.0-r31899 std (04/24/17)
Kernel Version: Linux 4.4.63 #1427 SMP Mon Apr 24 07:24:17 CEST 2017 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
USB 3.0 storage NTFS mount to MNT: NO, will not mount on reboot
NAS Samba shared drive: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless client’s output table

Repeater Bridge Build 31899 previous build 30949

Router: RT-AC66U - Repeater Bridge on 5 Ghz (AC-Only) to RT-AC87U
Firmware Version: DD-WRT v3.0-r31899 giga (04/24/17)
Kernel Version: Linux 3.10.105 #14534 Mon Apr 24 12:45:45 CEST 2017 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC-Only): OK
Reset via GUI: NO
Status: Working
Error(s): OK

_________________
Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6268
Location: Texas

PostPosted: Mon Apr 24, 2017 19:46    Post subject: Reply with quote
Many K3.x builds missing from
ftp://ftp.dd-wrt.com/betas/2017/04-24-2017-r31899/broadcom_K3X/

Was really looking for
dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin Confused
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6268
Location: Texas

PostPosted: Mon Apr 24, 2017 20:31    Post subject: Reply with quote
mrjcd wrote:
Many K3.x builds missing from
ftp://ftp.dd-wrt.com/betas/2017/04-24-2017-r31899/broadcom_K3X/

Was really looking for
dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin Confused

You just didn't look hard enough you goofball Rolling Eyes
-----
Install dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin on both units listed below over 31825 w/no reset.

Asus RT-N12D1 (shows as RT-N12B)
DD-WRT v3.0-r31899 mega (04/24/17)
Linux 3.10.105 #14554 Mon Apr 24 13:05:05 CEST 2017 mips
WAP + Guest
Working good so far.

Linksys E2500
DD-WRT v3.0-r31899 mega (04/24/17)
Linux 3.10.105 #14554 Mon Apr 24 13:05:05 CEST 2017
Test router running openVPN server.
Working ok.
OpenVPN server log is still blank in Status/OpenVPN tab. AFAIK this
is the case for all routers.... broadcom & atheros.

dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin is attached if anyone else wants it.



dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin
 Description:

Download
 Filename:  dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin
 Filesize:  7.24 MB
 Downloaded:  772 Time(s)

redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11563
Location: Wherever the wind blows- North America

PostPosted: Mon Apr 24, 2017 21:10    Post subject: Reply with quote
mrjcd wrote:
mrjcd wrote:
Many K3.x builds missing from
ftp://ftp.dd-wrt.com/betas/2017/04-24-2017-r31899/broadcom_K3X/

Was really looking for
dd-wrt.v24-31899_NEWD-2_K3.x_mega.bin Confused

You just didn't look hard enough you goofball Rolling Eyes


No...that's right...it doesn't show up for me either.

redhawk



list.jpg
 Description:
 Filesize:  212.91 KB
 Viewed:  19160 Time(s)

list.jpg



_________________
The only stupid question....is the unasked one.
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11563
Location: Wherever the wind blows- North America

PostPosted: Mon Apr 24, 2017 21:31    Post subject: Reply with quote
Router: e3000
Firmware: 31899 K3_mega.bin (supplied by link from mrjdc)
Status: Working with acceptions
Reset:no then yes
Errors: can't connect to USB stick until navigation to the Services/NAS tab and clicking apply. Then NAS works correctly. This has been going on for several builds.

None of my other NAS serving units (R7000's, WZR-600HP) exhibit this behavior...just this unit with K3 mega build installed.

redhawk

_________________
The only stupid question....is the unasked one.
smitna
DD-WRT Novice


Joined: 04 Jan 2011
Posts: 29
Location: Germany

PostPosted: Mon Apr 24, 2017 22:11    Post subject: Reply with quote
techpro2004 wrote:
update failed on rt-ac88u. It just shows the old build number/date on the top right corner of the web ui.


I can confirm. Same problem with all builds since r31690, still reported. But luckily we are the last ac88u owners who want to use DD-WRT, so nobody cares.
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7209
Location: Columbus, Ohio

PostPosted: Mon Apr 24, 2017 22:19    Post subject: Reply with quote
I wouldn't mind trying it but my rt-ac3100 has a new cfe and won't let me flash dd-wrt.
_________________
I am far from a guru, I'm barely a novice.
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Tue Apr 25, 2017 0:21    Post subject: Reply with quote
redhawk0 wrote:
Router: e3000
Firmware: 31899 K3_mega.bin (supplied by link from mrjdc)
Status: Working with acceptions
Reset:no then yes
Errors: can't connect to USB stick until navigation to the Services/NAS tab and clicking apply. Then NAS works correctly. This has been going on for several builds.

None of my other NAS serving units (R7000's, WZR-600HP) exhibit this behavior...just this unit with K3 mega build installed.

redhawk


Does toggling usb core support in the USB tab also make the stick available?

_________________
Kernel panic: Aiee, killing interrupt handler!
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11563
Location: Wherever the wind blows- North America

PostPosted: Tue Apr 25, 2017 12:56    Post subject: Reply with quote
LOM wrote:

Does toggling usb core support in the USB tab also make the stick available?


No....steps followed.

1 - Disable - Save
2 - Enable - Save
3- Check ftp access..."Unable to make connection...try again!"

4 - Disable - Apply
5 - Enable - Apply
6 - Check ftp access..."Unable to make connection...try again!"

7 - Navigate to NAS tab...click Save
8 - Check ftp access..."Unable to make connection...try again!"

9 - Click Apply - NAS now working.


Only clicking Apply from NAS tab allows access.

USB tab shows the stick is connected and gives statistics...says its mounted to /mnt (just /mnt /opts /jffs allowed in Mount Point pull down)

it shows statistics mounted as
/dev/sda giving a mount point as /mnt (see attached pic)

on a working R7000 unit this is mounted as
/dev/sda1 (different fw/kernel likely causing this) giving a mount point as /tmp/mnt/sda1

Does not show Diskspace / at all on the R7000

After a reboot...I have to manually go into the NAS tab and just click apply again to get things working.

redhawk



stats.jpg
 Description:
 Filesize:  141.04 KB
 Viewed:  18845 Time(s)

stats.jpg



_________________
The only stupid question....is the unasked one.
Bronk-S
DD-WRT User


Joined: 26 Jun 2012
Posts: 282

PostPosted: Tue Apr 25, 2017 13:03    Post subject: Reply with quote
Router: AC66U
Firmware: 31899
Kernel: 3.10.105 #14534
Status: Running
Reset: No
Errors: I just lost the management at the OpenVPN log, but al the rest looks to be working well.

Exact same behaviour for other units: WRT1900AC/ACS, EA8500, but since these aren't broadcom I presume you aren't interested. Wink

Any workaround to return back the management log ?

_________________
7 x Broadcom BCM5300 chip rev 1 - Asus RT-AC66U ----> v3.0-r31899 giga (04/24/17)
1 x Marvel Armada 385 - LinkSys WRT1900ACS ---------> v3.0-r31899 std (04/24/17)
1 x Marvel Armada 370/XP - LinkSys WRT1900AC -------> v3.0-r31899 std (04/24/17)
1 x QCA IPQ806X - Linksys EA8500 -------------------> v3.0-r31899 std (04/24/17)
1 x Broadcom BCM4709 - Asus RT-AC3200 --------------> v3.0-r30880 std (11/14/16)
1 x ARMv7 Processor rev 0 (v7l) - Asus RT-AC68U ----> v3.0-r30880 std (11/14/16)
1 x ARMv7 Processor rev 0 (v7l) - Linksys EA6900 ---> v3.0-r30880 std (11/14/16)
1 x ARM Cortex-A9 Processor - Net Gear R7000 -------> v3.0-r30880 std (11/14/16)
5 x Broadcom BCM4716 chip rev 1 - Linksys E4200 ----> v24-sp2 (06/07/14) kingkong
1 x Broadcom BCM5300 chip rev 1 - Asus RT-AC66U ----> v24-sp2 (04/01/13) giga

mwchang
DD-WRT Guru


Joined: 26 Mar 2013
Posts: 1855
Location: Hung Hom, Hong Kong

PostPosted: Tue Apr 25, 2017 15:13    Post subject: Reply with quote
Router Name: RT-N18U
Router Model: Asus RT-N18U
Firmware: DD-WRT v3.0-r31899 std (04/24/17)
Kernel: Linux 4.4.63 #1431 Mon Apr 24 08:02:39 CEST 2017 armv7l
Previous: DD-WRT v3.0-r31825 std (04/06/17)
Status: AP Working
Reset: NO reset during firmware upgrade
Errors: Working except USB (I don't use VPN)

1. Clicking Disable, Apply Settings, then Enable in Services->Core USB caused DD-WRT to reboot (crashed???). After reboot, Core USB remained Disabled. (need to reset data???)

2. LAN LED ... too lazy to check! Wink
3. DDNS function working normally and didn't crash like 31722
4. wireless working normally

Attached Speedtest result as image, using a 100M internet line provided by HKBN.



dd-wrt-31889-speedtest.png
 Description:
 Filesize:  21.31 KB
 Viewed:  18776 Time(s)

dd-wrt-31889-speedtest.png



_________________
Router: Asus RT-N18U (rev. A1)

Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!

Facebook: https://www.facebook.com/changmanwai
Website: https://sites.google.com/site/changmw
SETI@Home profile: http://setiathome.berkeley.edu/view_profile.php?userid=211832
GitHub: https://github.com/changmw/changmw
mwchang
DD-WRT Guru


Joined: 26 Mar 2013
Posts: 1855
Location: Hung Hom, Hong Kong

PostPosted: Tue Apr 25, 2017 15:24    Post subject: Reply with quote
LOM wrote:
Does toggling usb core support in the USB tab also make the stick available?

In my Asus RT-N18U, this action (Disable -> Apply -> Enable) caused DD-WRT to reboot. USB Core remained Disabled after reboot. Note that I didn't reset data during the firmware upgrade from 31825 to 31899.

BTW, the change log mentioned a ticket related to Samba.

Update: Problem solved

After you clicked "Enable" in USB Core, **BEFORE** hitting Apply Settings, you needed to disable USB Storage and USB Printer. After USB core was enabled, you could then enable USB Storage & USB Printer.

Suggestion to user interface changes:
Whenever someone disable USB Core, the interface should auto-magically disable USB Storage, USB Printer and USB over IP. Smile

_________________
Router: Asus RT-N18U (rev. A1)

Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!

Facebook: https://www.facebook.com/changmanwai
Website: https://sites.google.com/site/changmw
SETI@Home profile: http://setiathome.berkeley.edu/view_profile.php?userid=211832
GitHub: https://github.com/changmw/changmw
hubermania
DD-WRT User


Joined: 24 Aug 2012
Posts: 223

PostPosted: Wed Apr 26, 2017 3:44    Post subject: Reply with quote
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r31899 giga (04/24/17)
Previous: DD-WRT v3.0-r31825 giga
Kernel: Linux 3.10.105 #14534 Mon Apr 24 12:45:45 CEST 2017 mips
Status: OK but BusyBox wget command is broken (v1.26.2)
Reset: No
Errors: None

IPv6 DHCPv6 PD: OK
WAN/LAN ports: OK
2.4GHz AP: OK
5GHz AP: unused
Site Survey: OK
Wiviz Survey: OK
OpenVPN Client: OK tunneling IPv4+IPv6
USB Flash Drive: OK mounting /opt, /jffs, /swap partitions
CPU Temperature: WL0 46.3 °C / WL1 unused

_________________
[Broadcom] Asus rt-ac66u r35531 ('66 should only be factory reset through the DD UI)
Fix RT-AC66U "wl1 [2.4 GHz TurboQAM]". DD-WRT failsafe UI @ http|https://169.254.255.1/
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum