D-LINK DIR-860L B1 router

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
pesimeao
DD-WRT Novice


Joined: 27 Feb 2017
Posts: 2

PostPosted: Mon Feb 27, 2017 11:42    Post subject: Reply with quote
Hello,

I'm using the latest build, v3.0-r31277, from factory.
I feel that the 5Ghz band is not very stable. Sometimes I get dropped and I still don't know why yet.
I'm used to use DDWRT on another router (TP-Link Archer C5) and it works a lot better.

Anyway, I'm missing an important feature: wireless client mode. The only options available are AP, Adhoc, Repeater and Repeated bridged.
Is there any reason why Client mode is not available?

Thank you
Sponsor
wouterds
DD-WRT Novice


Joined: 14 Mar 2017
Posts: 2

PostPosted: Tue Mar 14, 2017 22:02    Post subject: Reply with quote
I love DD-WRT, but the 5Ghz performance on this device is just sad.
I'm not sure why, I think I've tried every setting and encryption.

It always eventually drops to around 5 Mbps and is just unusable.
The 2.4Ghz radio is fine though.
js1662
DD-WRT Guru


Joined: 23 Jul 2014
Posts: 1237
Location: BC, CA

PostPosted: Wed Mar 15, 2017 4:49    Post subject: Reply with quote
@wouterds, try using a higher channel between ch.149-165 and use 40MHz for channel bandwidth and see if it improves or not.
wouterds
DD-WRT Novice


Joined: 14 Mar 2017
Posts: 2

PostPosted: Wed Mar 15, 2017 17:43    Post subject: Reply with quote
js1662 wrote:
@wouterds, try using a higher channel between ch.149-165 and use 40MHz for channel bandwidth and see if it improves or not.


It's somewhat better but far from optimal, with stock firmware I can get up to 600Mbps connections. Also I remember using dd-wrt (a while ago, but on the same router, this one) and then also being able to get speeds up to 500Mbps.


Update: I re-flashed the router with the latest stable firmware, changed all my settings perfectly back they were before, and now I'm getting good speeds again!
pesimeao
DD-WRT Novice


Joined: 27 Feb 2017
Posts: 2

PostPosted: Sat Mar 25, 2017 9:23    Post subject: Reply with quote
@wouterds what version did you use?

I can't get good speeds anyway.
The behavior of the 5Ghz band is very very strange:

Here's my config:
1. I've the router connected to another one with repeater mode (2.4Ghz, N)
2. Configured 1 AP in 2.4Ghz
3. Configured 1 AP in 5Ghz.

Connected by cable I can download from the internet about 50mbps.
Connected to the 2.4Ghz network I can download about 16mbps (it's acceptable, I'm using the same bandwidth to connect to the other router).
Connected to the 5Ghz network the maximum I can get its 16mbps, just like I was connected to the 2.4Ghz! (I was expecting the same as the cable!)

Are there any thoughts about this?
crashnburn_in
DD-WRT Novice


Joined: 21 Jan 2012
Posts: 31

PostPosted: Mon Mar 27, 2017 12:00    Post subject: Reply with quote
wouterds wrote:
js1662 wrote:
@wouterds, try using a higher channel between ch.149-165 and use 40MHz for channel bandwidth and see if it improves or not.


It's somewhat better but far from optimal, with stock firmware I can get up to 600Mbps connections. Also I remember using dd-wrt (a while ago, but on the same router, this one) and then also being able to get speeds up to 500Mbps.


Update: I re-flashed the router with the latest stable firmware, changed all my settings perfectly back they were before, and now I'm getting good speeds again!


WHICH STABLE VERSION DO YOU MEAN? Stock D-Link or DD WRT Stable version "Number"?

Can you link to it please?
Your screenshot shows 24 sp2 while Stable does not have that.
ftp://ftp.dd-wrt.com/stable/

The one from your screenshot seems to be this?
ftp://ftp.dd-wrt.com/betas/2015/01-20-2015-r25974/dlink-dir860l-b1/
radmir
DD-WRT User


Joined: 26 Dec 2008
Posts: 153

PostPosted: Mon Apr 03, 2017 16:27    Post subject: Reply with quote
If anyone is interested I've compiled Padavan firmware for DIR-860L B1.
https://yadi.sk/d/6ttXcerpJ2hg3
No warranty. Backup your factory partition before flashing! Until you will not restore mtd2 router works unstable.
Code:
Jan  1 00:00:05 syslogd started: BusyBox v1.24.2
Jan  1 00:00:05 DIR-860L: firmware version: 3.4.3.9-099_3081e4e
Jan  1 00:00:05 kernel: klogd started: BusyBox v1.24.2 (2017-04-03 14:25:45 MSK)
Jan  1 00:00:05 kernel: Linux version 3.4.113 (padavan@hms) (gcc version 4.4.7 (GCC) ) #1 SMP Mon Apr 3 14:18:36 MSK 2017
Jan  1 00:00:05 kernel: MediaTek SoC: MT7621A, RevID: 0103, RAM: DDR3, XTAL: 40MHz
Jan  1 00:00:05 kernel: CPU/OCP/SYS frequency: 900/300/225 MHz
Jan  1 00:00:05 kernel: CPU sleep mode: ON
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Determined physical RAM map:
Jan  1 00:00:05 kernel:  memory: 08000000 @ 00000000 (usable)
Jan  1 00:00:05 kernel: Zone PFN ranges:
Jan  1 00:00:05 kernel:   Normal   0x00000000 -> 0x00008000
Jan  1 00:00:05 kernel: Movable zone start PFN for each node
Jan  1 00:00:05 kernel: Early memory PFN ranges
Jan  1 00:00:05 kernel:     0: 0x00000000 -> 0x00008000
Jan  1 00:00:05 kernel: On node 0 totalpages: 32768
Jan  1 00:00:05 kernel: free_area_init_node: node 0, pgdat 80358900, node_mem_map 81000000
Jan  1 00:00:05 kernel:   Normal zone: 256 pages used for memmap
Jan  1 00:00:05 kernel:   Normal zone: 0 pages reserved
Jan  1 00:00:05 kernel:   Normal zone: 32512 pages, LIFO batch:7
Jan  1 00:00:05 kernel: Detected 3 available secondary CPU(s)
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: PERCPU: Embedded 7 pages/cpu @81103000 s5760 r8192 d14720 u32768
Jan  1 00:00:05 kernel: pcpu-alloc: s5760 r8192 d14720 u32768 alloc=8*4096
Jan  1 00:00:05 kernel: pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Jan  1 00:00:05 kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Jan  1 00:00:05 kernel: Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs
Jan  1 00:00:05 kernel: PID hash table entries: 512 (order: -1, 2048 bytes)
Jan  1 00:00:05 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:05 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: Writing ErrCtl register=00060041
Jan  1 00:00:05 kernel: Readback ErrCtl register=00060041
Jan  1 00:00:05 kernel: Memory: 126056k/131072k available (2991k kernel code, 5016k reserved, 432k data, 220k init, 0k highmem)
Jan  1 00:00:05 kernel: Hierarchical RCU implementation.
Jan  1 00:00:05 kernel: NR_IRQS:72
Jan  1 00:00:05 kernel: MIPS GIC RevID: 3.0
Jan  1 00:00:05 kernel: Setting up vectored interrupts
Jan  1 00:00:05 kernel: console [ttyS0] enabled
Jan  1 00:00:05 kernel: Calibrating delay loop... 598.01 BogoMIPS (lpj=299008)
Jan  1 00:00:05 kernel: pid_max: default: 32768 minimum: 301
Jan  1 00:00:05 kernel: Mount-cache hash table entries: 512
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 1: done.
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 2: done.
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 3: done.
Jan  1 00:00:05 kernel: Brought up 4 CPUs
Jan  1 00:00:05 kernel: NET: Registered protocol family 16
Jan  1 00:00:05 kernel: FPU Affinity set after 188 emulations
Jan  1 00:00:05 kernel: bio: create slab <bio-0> at 0
Jan  1 00:00:05 kernel: SCSI subsystem initialized
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usbfs
Jan  1 00:00:05 kernel: usbcore: registered new interface driver hub
Jan  1 00:00:05 kernel: usbcore: registered new device driver usb
Jan  1 00:00:05 kernel: PCI host bridge to bus 0000:00
Jan  1 00:00:05 kernel: pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
Jan  1 00:00:05 kernel: pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
Jan  1 00:00:05 kernel: pci 0000:00:00.0: supports D1
Jan  1 00:00:05 kernel: pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan  1 00:00:05 kernel: pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
Jan  1 00:00:05 kernel: pci 0000:00:01.0: supports D1
Jan  1 00:00:05 kernel: pci 0000:00:01.0: PME# supported from D0 D1 D3hot
Jan  1 00:00:05 kernel: pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
Jan  1 00:00:05 kernel: pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Jan  1 00:00:05 kernel: pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
Jan  1 00:00:05 kernel: pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
Jan  1 00:00:05 kernel: pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: PCI bridge to [bus 01-01]
Jan  1 00:00:05 kernel: pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: PCI bridge to [bus 02-02]
Jan  1 00:00:05 kernel: pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
Jan  1 00:00:05 kernel: pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
Jan  1 00:00:05 kernel: Switching to clocksource Ralink Systick Timer
Jan  1 00:00:05 kernel: NET: Registered protocol family 2
Jan  1 00:00:05 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 00:00:05 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan  1 00:00:05 kernel: TCP: reno registered
Jan  1 00:00:05 kernel: UDP hash table entries: 128 (order: 0, 4096 bytes)
Jan  1 00:00:05 kernel: NET: Registered protocol family 1
Jan  1 00:00:05 kernel: PCI: CLS 32 bytes, default 32
Jan  1 00:00:05 kernel: 4 CPUs re-calibrate udelay (lpj = 297984)
Jan  1 00:00:05 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 00:00:05 kernel: msgmni has been set to 246
Jan  1 00:00:05 kernel: io scheduler noop registered (default)
Jan  1 00:00:05 kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jan  1 00:00:05 kernel: serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Jan  1 00:00:05 kernel: Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 000405AC
Jan  1 00:00:05 kernel: loop: module loaded
Jan  1 00:00:05 kernel: MediaTek SPI flash driver, SPI clock: 45MHz
Jan  1 00:00:05 kernel: SPI flash chip: MX25L12835F (c2 2018c220) (16384 Kbytes)
Jan  1 00:00:05 kernel: Creating 7 MTD partitions on "raspi":
Jan  1 00:00:05 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Jan  1 00:00:05 kernel: 0x000000030000-0x000000040000 : "Config"
Jan  1 00:00:05 kernel: 0x000000040000-0x000000050000 : "Factory"
Jan  1 00:00:05 kernel: 0x000000050000-0x000000182bf0 : "Kernel"
Jan  1 00:00:05 kernel: 0x000000182bf0-0x000000fc0000 : "RootFS"
Jan  1 00:00:05 kernel: 0x000000fc0000-0x000001000000 : "Storage"
Jan  1 00:00:05 kernel: 0x000000050000-0x000000fc0000 : "Firmware_Stub"
Jan  1 00:00:05 kernel: tun: Universal TUN/TAP device driver, 1.6
Jan  1 00:00:05 kernel: tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan  1 00:00:05 kernel: Ralink APSoC Ethernet Driver v3.2.4 (raeth)
Jan  1 00:00:05 kernel: raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
Jan  1 00:00:05 kernel: raeth: NAPI & GRO support, weight 64
Jan  1 00:00:05 kernel: raeth: Byte Queue Limits (BQL) support
Jan  1 00:00:05 kernel: PPP generic driver version 2.4.2
Jan  1 00:00:05 kernel: PPP MPPE Compression module registered
Jan  1 00:00:05 kernel: NET: Registered protocol family 24
Jan  1 00:00:05 kernel: PPTP driver version 0.8.5
Jan  1 00:00:05 kernel: usbcore: registered new interface driver libusual
Jan  1 00:00:05 kernel: nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
Jan  1 00:00:05 kernel: xt_time: kernel timezone is -0000
Jan  1 00:00:05 kernel: Bridge firewalling registered
Jan  1 00:00:05 kernel: gre: GRE over IPv4 demultiplexor driver
Jan  1 00:00:05 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:05 kernel: TCP: cubic registered
Jan  1 00:00:05 kernel: NET: Registered protocol family 10
Jan  1 00:00:05 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:05 kernel: IPv6 over IPv4 tunneling driver
Jan  1 00:00:05 kernel: NET: Registered protocol family 17
Jan  1 00:00:05 kernel: L2TP core driver, V2.0
Jan  1 00:00:05 kernel: PPPoL2TP kernel driver, V2.0
Jan  1 00:00:05 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan  1 00:00:05 kernel: ASUS NVRAM, v0.08. Available space: 61440. Integrity: OK
Jan  1 00:00:05 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan  1 00:00:05 kernel: Freeing unused kernel memory: 220k freed
Jan  1 00:00:05 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan  1 00:00:05 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Jan  1 00:00:05 kernel: MT76x2 AP Driver version: 3.0.5.0
Jan  1 00:00:05 kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan  1 00:00:05 kernel: MT76x2 AP Driver version: 3.0.5.0
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usblp
Jan  1 00:00:05 kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usb-storage
Jan  1 00:00:05 kernel: USB Mass Storage support registered.
Jan  1 00:00:05 kernel: U2PHY P0 set SRCTRL calibration value: 2
Jan  1 00:00:05 kernel: U2PHY P1 set SRCTRL calibration value: 2
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
Jan  1 00:00:05 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan  1 00:00:05 kernel: usb usb1: Product: xHCI Host Controller
Jan  1 00:00:05 kernel: usb usb1: Manufacturer: Linux 3.4.113 xhci-hcd
Jan  1 00:00:05 kernel: usb usb1: SerialNumber: xhci-hcd
Jan  1 00:00:05 kernel: xHCI xhci_add_endpoint called for root hub
Jan  1 00:00:05 kernel: xHCI xhci_check_bandwidth called for root hub
Jan  1 00:00:05 kernel: hub 1-0:1.0: USB hub found
Jan  1 00:00:05 kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:05 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
Jan  1 00:00:05 kernel: usb usb2: Product: xHCI Host Controller
Jan  1 00:00:05 kernel: usb usb2: Manufacturer: Linux 3.4.113 xhci-hcd
Jan  1 00:00:05 kernel: usb usb2: SerialNumber: xhci-hcd
Jan  1 00:00:05 kernel: xHCI xhci_add_endpoint called for root hub
Jan  1 00:00:05 kernel: xHCI xhci_check_bandwidth called for root hub
Jan  1 00:00:05 kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:05 kernel: hub 2-0:1.0: 1 port detected
Jan  1 00:00:05 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW VLAN RX offload enabled
Jan  1 00:00:05 kernel: raeth: HW VLAN TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW Scatter/Gather TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW TCP segmentation offload (TSO) enabled
Jan  1 00:00:05 kernel: mtk_esw - hw bridge: W|LLLL
Jan  1 00:00:05 kernel: mtk_esw - 802.3az EEE: on
Jan  1 00:00:05 kernel: mtk_esw - set broadcast storm control rate as: 10 mbps
Jan  1 00:00:05 kernel: device eth2 entered promiscuous mode
Jan  1 00:00:07 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
Jan  1 00:00:07 kernel: =====================================================
Jan  1 00:00:07 kernel: Channel 36 : Dirty = 0, False CCA = 72, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 40 : Dirty = 0, False CCA = 3252, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 44 : Dirty = 0, False CCA = 123, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 48 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: =====================================================
Jan  1 00:00:07 kernel: Rule 2 CCA value : Min False CCA value ==> Select Channel 40, min falsecca = 3447
Jan  1 00:00:08 kernel: device rai0 entered promiscuous mode
Jan  1 00:00:11 kernel:  ch1 bssid=64:70:02:a1:de:42
Jan  1 00:00:11 kernel:  ch1 bssid=90:f6:52:52:31:1e
Jan  1 00:00:11 kernel:  ch1 bssid=96:fa:58:2e:9f:47
Jan  1 00:00:11 kernel:  ch6 bssid=c4:6e:1f:ba:55:12
Jan  1 00:00:11 kernel:  ch7 bssid=04:bf:6d:94:2f:68
Jan  1 00:00:11 kernel:  ch8 bssid=98:de:d0:a9:a6:5a
Jan  1 00:00:11 kernel:  ch8 bssid=68:72:51:38:ce:69
Jan  1 00:00:11 kernel:  ch9 bssid=e8:de:27:ec:bc:ba
Jan  1 00:00:12 kernel: =====================================================
Jan  1 00:00:12 kernel: Channel 1 : Dirty = 210, False CCA = 413, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 2 : Dirty = 116, False CCA = 328, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 3 : Dirty = 128, False CCA = 249, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 4 : Dirty = 164, False CCA = 238, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 5 : Dirty = 188, False CCA = 3383, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 6 : Dirty = 192, False CCA = 13358, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 7 : Dirty = 194, False CCA = 8184, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 8 : Dirty = 232, False CCA = 5412, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 9 : Dirty = 186, False CCA = 906, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 10 : Dirty = 132, False CCA = 844, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 11 : Dirty = 96, False CCA = 350, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: =====================================================
Jan  1 00:00:12 kernel: Rule 2 CCA value : Min False CCA value ==> Select Channel 3, min falsecca = 377
Jan  1 00:00:12 kernel: device ra0 entered promiscuous mode
Jan  1 00:00:13 kernel: br0: port 3(ra0) entered forwarding state
Jan  1 00:00:13 kernel: br0: port 2(rai0) entered forwarding state
Jan  1 00:00:13 kernel: br0: port 1(eth2) entered forwarding state
Jan  1 00:00:13 kernel: mtk_esw - software IGMP/MLD snooping: 1
Jan  1 00:00:13 dnsmasq[408]: started, version 2.76 cachesize 1024
Jan  1 00:00:13 dnsmasq[408]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Jan  1 00:00:13 dnsmasq-dhcp[408]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Jan  1 00:00:13 dnsmasq-dhcp[408]: DHCP, sockets bound exclusively to interface br0
Jan  1 00:00:13 dnsmasq[408]: read /etc/hosts - 3 addresses
Jan  1 00:00:13 dnsmasq[408]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan  1 00:00:13 dnsmasq-dhcp[408]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan  1 00:00:13 kernel: eth3: ===> VirtualIF_open
Jan  1 00:00:14 kernel: Ralink HW NAT v2.52.0 Module Enabled, FoE Size: 16384
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload [WAN]<->[LAN/WLAN]
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: IPv4 UDP flow offload - ON
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan  1 00:00:14 DHCP MAN Client: starting on eth3 ...
Jan  1 00:00:14 DHCP MAN Client: bound (eth3), IP: 10.19.3.28, GW: 10.19.0.1, lease time: 86400
Jan  1 00:00:14 DIR-860L: MAN up (eth3)
crashnburn_in
DD-WRT Novice


Joined: 21 Jan 2012
Posts: 31

PostPosted: Tue Apr 04, 2017 6:39    Post subject: Reply with quote
Thanks for sharing. Please do share how it is compared to DD WRT and/ stock firmware.

radmir wrote:
If anyone is interested I've compiled Padavan firmware for DIR-860L B1.
https://yadi.sk/d/6ttXcerpJ2hg3
No warranty. Backup your factory partition before flashing! Until you will not restore mtd2 router works unstable.
Code:
Jan  1 00:00:05 syslogd started: BusyBox v1.24.2
Jan  1 00:00:05 DIR-860L: firmware version: 3.4.3.9-099_3081e4e
Jan  1 00:00:05 kernel: klogd started: BusyBox v1.24.2 (2017-04-03 14:25:45 MSK)
Jan  1 00:00:05 kernel: Linux version 3.4.113 (padavan@hms) (gcc version 4.4.7 (GCC) ) #1 SMP Mon Apr 3 14:18:36 MSK 2017
Jan  1 00:00:05 kernel: MediaTek SoC: MT7621A, RevID: 0103, RAM: DDR3, XTAL: 40MHz
Jan  1 00:00:05 kernel: CPU/OCP/SYS frequency: 900/300/225 MHz
Jan  1 00:00:05 kernel: CPU sleep mode: ON
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Determined physical RAM map:
Jan  1 00:00:05 kernel:  memory: 08000000 @ 00000000 (usable)
Jan  1 00:00:05 kernel: Zone PFN ranges:
Jan  1 00:00:05 kernel:   Normal   0x00000000 -> 0x00008000
Jan  1 00:00:05 kernel: Movable zone start PFN for each node
Jan  1 00:00:05 kernel: Early memory PFN ranges
Jan  1 00:00:05 kernel:     0: 0x00000000 -> 0x00008000
Jan  1 00:00:05 kernel: On node 0 totalpages: 32768
Jan  1 00:00:05 kernel: free_area_init_node: node 0, pgdat 80358900, node_mem_map 81000000
Jan  1 00:00:05 kernel:   Normal zone: 256 pages used for memmap
Jan  1 00:00:05 kernel:   Normal zone: 0 pages reserved
Jan  1 00:00:05 kernel:   Normal zone: 32512 pages, LIFO batch:7
Jan  1 00:00:05 kernel: Detected 3 available secondary CPU(s)
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: PERCPU: Embedded 7 pages/cpu @81103000 s5760 r8192 d14720 u32768
Jan  1 00:00:05 kernel: pcpu-alloc: s5760 r8192 d14720 u32768 alloc=8*4096
Jan  1 00:00:05 kernel: pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Jan  1 00:00:05 kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Jan  1 00:00:05 kernel: Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs
Jan  1 00:00:05 kernel: PID hash table entries: 512 (order: -1, 2048 bytes)
Jan  1 00:00:05 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:05 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: Writing ErrCtl register=00060041
Jan  1 00:00:05 kernel: Readback ErrCtl register=00060041
Jan  1 00:00:05 kernel: Memory: 126056k/131072k available (2991k kernel code, 5016k reserved, 432k data, 220k init, 0k highmem)
Jan  1 00:00:05 kernel: Hierarchical RCU implementation.
Jan  1 00:00:05 kernel: NR_IRQS:72
Jan  1 00:00:05 kernel: MIPS GIC RevID: 3.0
Jan  1 00:00:05 kernel: Setting up vectored interrupts
Jan  1 00:00:05 kernel: console [ttyS0] enabled
Jan  1 00:00:05 kernel: Calibrating delay loop... 598.01 BogoMIPS (lpj=299008)
Jan  1 00:00:05 kernel: pid_max: default: 32768 minimum: 301
Jan  1 00:00:05 kernel: Mount-cache hash table entries: 512
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 1: done.
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 2: done.
Jan  1 00:00:05 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:05 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 00:00:05 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 00:00:05 kernel: Synchronize counters for CPU 3: done.
Jan  1 00:00:05 kernel: Brought up 4 CPUs
Jan  1 00:00:05 kernel: NET: Registered protocol family 16
Jan  1 00:00:05 kernel: FPU Affinity set after 188 emulations
Jan  1 00:00:05 kernel: bio: create slab <bio-0> at 0
Jan  1 00:00:05 kernel: SCSI subsystem initialized
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usbfs
Jan  1 00:00:05 kernel: usbcore: registered new interface driver hub
Jan  1 00:00:05 kernel: usbcore: registered new device driver usb
Jan  1 00:00:05 kernel: PCI host bridge to bus 0000:00
Jan  1 00:00:05 kernel: pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
Jan  1 00:00:05 kernel: pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
Jan  1 00:00:05 kernel: pci 0000:00:00.0: supports D1
Jan  1 00:00:05 kernel: pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan  1 00:00:05 kernel: pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
Jan  1 00:00:05 kernel: pci 0000:00:01.0: supports D1
Jan  1 00:00:05 kernel: pci 0000:00:01.0: PME# supported from D0 D1 D3hot
Jan  1 00:00:05 kernel: pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
Jan  1 00:00:05 kernel: pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Jan  1 00:00:05 kernel: pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
Jan  1 00:00:05 kernel: pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
Jan  1 00:00:05 kernel: pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:00.0: PCI bridge to [bus 01-01]
Jan  1 00:00:05 kernel: pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
Jan  1 00:00:05 kernel: pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
Jan  1 00:00:05 kernel: pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
Jan  1 00:00:05 kernel: pci 0000:00:01.0: PCI bridge to [bus 02-02]
Jan  1 00:00:05 kernel: pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
Jan  1 00:00:05 kernel: pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
Jan  1 00:00:05 kernel: Switching to clocksource Ralink Systick Timer
Jan  1 00:00:05 kernel: NET: Registered protocol family 2
Jan  1 00:00:05 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 00:00:05 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 00:00:05 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan  1 00:00:05 kernel: TCP: reno registered
Jan  1 00:00:05 kernel: UDP hash table entries: 128 (order: 0, 4096 bytes)
Jan  1 00:00:05 kernel: NET: Registered protocol family 1
Jan  1 00:00:05 kernel: PCI: CLS 32 bytes, default 32
Jan  1 00:00:05 kernel: 4 CPUs re-calibrate udelay (lpj = 297984)
Jan  1 00:00:05 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 00:00:05 kernel: msgmni has been set to 246
Jan  1 00:00:05 kernel: io scheduler noop registered (default)
Jan  1 00:00:05 kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jan  1 00:00:05 kernel: serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Jan  1 00:00:05 kernel: Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 000405AC
Jan  1 00:00:05 kernel: loop: module loaded
Jan  1 00:00:05 kernel: MediaTek SPI flash driver, SPI clock: 45MHz
Jan  1 00:00:05 kernel: SPI flash chip: MX25L12835F (c2 2018c220) (16384 Kbytes)
Jan  1 00:00:05 kernel: Creating 7 MTD partitions on "raspi":
Jan  1 00:00:05 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Jan  1 00:00:05 kernel: 0x000000030000-0x000000040000 : "Config"
Jan  1 00:00:05 kernel: 0x000000040000-0x000000050000 : "Factory"
Jan  1 00:00:05 kernel: 0x000000050000-0x000000182bf0 : "Kernel"
Jan  1 00:00:05 kernel: 0x000000182bf0-0x000000fc0000 : "RootFS"
Jan  1 00:00:05 kernel: 0x000000fc0000-0x000001000000 : "Storage"
Jan  1 00:00:05 kernel: 0x000000050000-0x000000fc0000 : "Firmware_Stub"
Jan  1 00:00:05 kernel: tun: Universal TUN/TAP device driver, 1.6
Jan  1 00:00:05 kernel: tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan  1 00:00:05 kernel: Ralink APSoC Ethernet Driver v3.2.4 (raeth)
Jan  1 00:00:05 kernel: raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
Jan  1 00:00:05 kernel: raeth: NAPI & GRO support, weight 64
Jan  1 00:00:05 kernel: raeth: Byte Queue Limits (BQL) support
Jan  1 00:00:05 kernel: PPP generic driver version 2.4.2
Jan  1 00:00:05 kernel: PPP MPPE Compression module registered
Jan  1 00:00:05 kernel: NET: Registered protocol family 24
Jan  1 00:00:05 kernel: PPTP driver version 0.8.5
Jan  1 00:00:05 kernel: usbcore: registered new interface driver libusual
Jan  1 00:00:05 kernel: nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
Jan  1 00:00:05 kernel: xt_time: kernel timezone is -0000
Jan  1 00:00:05 kernel: Bridge firewalling registered
Jan  1 00:00:05 kernel: gre: GRE over IPv4 demultiplexor driver
Jan  1 00:00:05 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:05 kernel: TCP: cubic registered
Jan  1 00:00:05 kernel: NET: Registered protocol family 10
Jan  1 00:00:05 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:05 kernel: IPv6 over IPv4 tunneling driver
Jan  1 00:00:05 kernel: NET: Registered protocol family 17
Jan  1 00:00:05 kernel: L2TP core driver, V2.0
Jan  1 00:00:05 kernel: PPPoL2TP kernel driver, V2.0
Jan  1 00:00:05 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan  1 00:00:05 kernel: ASUS NVRAM, v0.08. Available space: 61440. Integrity: OK
Jan  1 00:00:05 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan  1 00:00:05 kernel: Freeing unused kernel memory: 220k freed
Jan  1 00:00:05 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan  1 00:00:05 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Jan  1 00:00:05 kernel: MT76x2 AP Driver version: 3.0.5.0
Jan  1 00:00:05 kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan  1 00:00:05 kernel: MT76x2 AP Driver version: 3.0.5.0
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usblp
Jan  1 00:00:05 kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:05 kernel: usbcore: registered new interface driver usb-storage
Jan  1 00:00:05 kernel: USB Mass Storage support registered.
Jan  1 00:00:05 kernel: U2PHY P0 set SRCTRL calibration value: 2
Jan  1 00:00:05 kernel: U2PHY P1 set SRCTRL calibration value: 2
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
Jan  1 00:00:05 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan  1 00:00:05 kernel: usb usb1: Product: xHCI Host Controller
Jan  1 00:00:05 kernel: usb usb1: Manufacturer: Linux 3.4.113 xhci-hcd
Jan  1 00:00:05 kernel: usb usb1: SerialNumber: xhci-hcd
Jan  1 00:00:05 kernel: xHCI xhci_add_endpoint called for root hub
Jan  1 00:00:05 kernel: xHCI xhci_check_bandwidth called for root hub
Jan  1 00:00:05 kernel: hub 1-0:1.0: USB hub found
Jan  1 00:00:05 kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 00:00:05 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:05 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
Jan  1 00:00:05 kernel: usb usb2: Product: xHCI Host Controller
Jan  1 00:00:05 kernel: usb usb2: Manufacturer: Linux 3.4.113 xhci-hcd
Jan  1 00:00:05 kernel: usb usb2: SerialNumber: xhci-hcd
Jan  1 00:00:05 kernel: xHCI xhci_add_endpoint called for root hub
Jan  1 00:00:05 kernel: xHCI xhci_check_bandwidth called for root hub
Jan  1 00:00:05 kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:05 kernel: hub 2-0:1.0: 1 port detected
Jan  1 00:00:05 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW VLAN RX offload enabled
Jan  1 00:00:05 kernel: raeth: HW VLAN TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW Scatter/Gather TX offload enabled
Jan  1 00:00:05 kernel: raeth: HW TCP segmentation offload (TSO) enabled
Jan  1 00:00:05 kernel: mtk_esw - hw bridge: W|LLLL
Jan  1 00:00:05 kernel: mtk_esw - 802.3az EEE: on
Jan  1 00:00:05 kernel: mtk_esw - set broadcast storm control rate as: 10 mbps
Jan  1 00:00:05 kernel: device eth2 entered promiscuous mode
Jan  1 00:00:07 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
Jan  1 00:00:07 kernel: =====================================================
Jan  1 00:00:07 kernel: Channel 36 : Dirty = 0, False CCA = 72, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 40 : Dirty = 0, False CCA = 3252, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 44 : Dirty = 0, False CCA = 123, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: Channel 48 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:07 kernel: =====================================================
Jan  1 00:00:07 kernel: Rule 2 CCA value : Min False CCA value ==> Select Channel 40, min falsecca = 3447
Jan  1 00:00:08 kernel: device rai0 entered promiscuous mode
Jan  1 00:00:11 kernel:  ch1 bssid=64:70:02:a1:de:42
Jan  1 00:00:11 kernel:  ch1 bssid=90:f6:52:52:31:1e
Jan  1 00:00:11 kernel:  ch1 bssid=96:fa:58:2e:9f:47
Jan  1 00:00:11 kernel:  ch6 bssid=c4:6e:1f:ba:55:12
Jan  1 00:00:11 kernel:  ch7 bssid=04:bf:6d:94:2f:68
Jan  1 00:00:11 kernel:  ch8 bssid=98:de:d0:a9:a6:5a
Jan  1 00:00:11 kernel:  ch8 bssid=68:72:51:38:ce:69
Jan  1 00:00:11 kernel:  ch9 bssid=e8:de:27:ec:bc:ba
Jan  1 00:00:12 kernel: =====================================================
Jan  1 00:00:12 kernel: Channel 1 : Dirty = 210, False CCA = 413, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 2 : Dirty = 116, False CCA = 328, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 3 : Dirty = 128, False CCA = 249, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 4 : Dirty = 164, False CCA = 238, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 5 : Dirty = 188, False CCA = 3383, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 6 : Dirty = 192, False CCA = 13358, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 7 : Dirty = 194, False CCA = 8184, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 8 : Dirty = 232, False CCA = 5412, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 9 : Dirty = 186, False CCA = 906, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 10 : Dirty = 132, False CCA = 844, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: Channel 11 : Dirty = 96, False CCA = 350, Busy Time = 0, Skip Channel = FALSE
Jan  1 00:00:12 kernel: =====================================================
Jan  1 00:00:12 kernel: Rule 2 CCA value : Min False CCA value ==> Select Channel 3, min falsecca = 377
Jan  1 00:00:12 kernel: device ra0 entered promiscuous mode
Jan  1 00:00:13 kernel: br0: port 3(ra0) entered forwarding state
Jan  1 00:00:13 kernel: br0: port 2(rai0) entered forwarding state
Jan  1 00:00:13 kernel: br0: port 1(eth2) entered forwarding state
Jan  1 00:00:13 kernel: mtk_esw - software IGMP/MLD snooping: 1
Jan  1 00:00:13 dnsmasq[408]: started, version 2.76 cachesize 1024
Jan  1 00:00:13 dnsmasq[408]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Jan  1 00:00:13 dnsmasq-dhcp[408]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Jan  1 00:00:13 dnsmasq-dhcp[408]: DHCP, sockets bound exclusively to interface br0
Jan  1 00:00:13 dnsmasq[408]: read /etc/hosts - 3 addresses
Jan  1 00:00:13 dnsmasq[408]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan  1 00:00:13 dnsmasq-dhcp[408]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan  1 00:00:13 kernel: eth3: ===> VirtualIF_open
Jan  1 00:00:14 kernel: Ralink HW NAT v2.52.0 Module Enabled, FoE Size: 16384
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload [WAN]<->[LAN/WLAN]
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: IPv4 UDP flow offload - ON
Jan  1 00:00:14 DIR-860L: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan  1 00:00:14 DHCP MAN Client: starting on eth3 ...
Jan  1 00:00:14 DHCP MAN Client: bound (eth3), IP: 10.19.3.28, GW: 10.19.0.1, lease time: 86400
Jan  1 00:00:14 DIR-860L: MAN up (eth3)
radmir
DD-WRT User


Joined: 26 Dec 2008
Posts: 153

PostPosted: Tue Apr 04, 2017 7:12    Post subject: Reply with quote
crashnburn_in wrote:
Please do share how it is compared to DD WRT and/ stock firmware.

Can't compare becouse I compiled Padavan's first build next day I got 860L. No any issue. Works stable. I aslo increased wifi power levels for USA region.
crashnburn_in
DD-WRT Novice


Joined: 21 Jan 2012
Posts: 31

PostPosted: Tue Apr 04, 2017 8:44    Post subject: Reply with quote
radmir wrote:
crashnburn_in wrote:
Please do share how it is compared to DD WRT and/ stock firmware.

Can't compare becouse I compiled Padavan's first build next day I got 860L. No any issue. Works stable. I aslo increased wifi power levels for USA region.


Oh ok. For what reason(s) did you chose/ prefer this FW over DD WRT?
radmir
DD-WRT User


Joined: 26 Dec 2008
Posts: 153

PostPosted: Tue Apr 04, 2017 8:47    Post subject: Reply with quote
IMO Stability. Perfomance. Padavan uses native MTK drivers.
Huck
DD-WRT Novice


Joined: 06 Apr 2017
Posts: 11

PostPosted: Thu Apr 06, 2017 23:04    Post subject: Reply with quote
radmir wrote:
crashnburn_in wrote:
Please do share how it is compared to DD WRT and/ stock firmware.

Can't compare becouse I compiled Padavan's first build next day I got 860L. No any issue. Works stable. I aslo increased wifi power levels for USA region.


I just joined this forum after years of being just a reader. So I could say thanks. WOW, most appreciated.

I've used your padavan builds from the n750 thread since the day I bought the old belkin and its still my main router.

I bought a 860l b1 off ebay about a month ago running dd-wrt(feb build). It was recommend by many in the opensource community plus its hard to brick with its reset recovery menu.

Is there a proper procedure to flash padavan to the 860l? I read you mentioned to back up partition first.

Can it be flashed as simply as thru the dlink reset recovery menu?

Will we lose the reset recovery menu with padavan firmware?

Again a huge thanks for your time.
radmir
DD-WRT User


Joined: 26 Dec 2008
Posts: 153

PostPosted: Fri Apr 07, 2017 7:39    Post subject: Reply with quote
Huck wrote:
Is there a proper procedure to flash padavan to the 860l?

I’m not 100% sure about DD-WRT commands.
Put DIR-860L_3.4.3.9-099.trx and mtd2.bin on usb flash drive.
From DD-WRT connect via telnet:
cd {path to your usb drive}
cat /dev/mtdblock1 > mymtd1.bin
cat /dev/mtdblock2 > mymtd2.bin
mtd write -r DIR-860L_3.4.3.9-099.trx linux
When router powers up connect via ssh (login/pass admin/admin):
cd {path to your usb drive (/media/…)}
mtd_write write -r mtd2.bin "Factory"
Now router should be fully functional.
You can correct MAC addresses by commands lan_eeprom_mac, wan_eeprom_mac, radio2_eeprom_mac and radio5_eeprom_mac.
It is always possible to restore by recovery mode to stock or DD-WRT firmware. On DD-WRT restore your backup: mtd write -r mymtd2.bin "factory".
...
P.S. Image updated, USB led added.
P.P.S. 'factory' image doesn't work. So only way to flash is from telnet.
DD-WRT/OpenWRT/Padavan uses different partition layouts. Padavan uses 0x000000040000-0x000000050000 region for wifi eeprom. DD-WRT doesnt' use this region at all and it's 'defaults' partition in OpenWRT.
Huck
DD-WRT Novice


Joined: 06 Apr 2017
Posts: 11

PostPosted: Sun Apr 09, 2017 19:05    Post subject: Reply with quote
radmir wrote:
Huck wrote:
Is there a proper procedure to flash padavan to the 860l?

I’m not 100% sure about DD-WRT commands.

mtd write -r DIR-860L_3.4.3.9-099.trx linux


Its been a few years since I played with dd-wrt myself.Not since I got this router.
Thanks again for all the help.

I did back up mymtd1.bin and mymtd2.bin.

I was able to write the firmware and reboot if I use:
mtd -r write DIR-860L_3.4.3.9-099.trx linux.

but after reboot it won't allow an ssh connection to complete the second part
mtd_write write -r mtd2.bin "Factory"

After reboot only the dlink reset recovery menu method works to restore an image. Neither ssh and telnet were connecting.


But If I use
mtd write DIR-860L_3.4.3.9-099.trx linux

It writes without reboot and I don't lose connection to the router.
Is it ok to skip the reboot? and write thru the same telnet connection
mtd_write write -r mtd2.bin "Factory"

Or do you need that reboot and ssh connection to write correctly mtd2.bin?

My main concern is losing dlink's recovery menu partition since its the only thing that keeps this router going so easily.

Again thanks for all your time.
radmir
DD-WRT User


Joined: 26 Dec 2008
Posts: 153

PostPosted: Sun Apr 09, 2017 19:39    Post subject: Reply with quote
Huck wrote:
Neither ssh and telnet were connecting.

I managed to connect via 5G, maybe wired connection also will works.
Quote:
Is it ok to skip the reboot? and write thru the same telnet connection
mtd_write write -r mtd2.bin "Factory"

Or do you need that reboot and ssh connection to write correctly mtd2.bin?

No. Partition layouts are different. You can try to flash from OpenWRT to 'defaults' partition.
Quote:
My main concern is losing dlink's recovery menu partition since its the only thing that keeps this router going so easily.
It doesn't flash bootloader.
My router works rock stable with Padavan FW.
...
Updated mtd2.bin to default D-Link EEPROMs.
Goto page Previous  1, 2, 3, 4, 5, 6  Next Display posts from previous:    Page 2 of 6
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum