Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Posted: Fri Oct 07, 2016 16:20 Post subject: Asus RT-AC68U & 2 Linksys E2000
Asus RT-AC68U
asus_rt-ac68u-firmware r30731 (previous r30709)
Kernel: 4.4.23 #1460 SMP Tue Oct 4 08:53:28 CEST 2016 armv7l DD-WRT
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: No
Status: Ok
Uptime: 10 minutes
CPU Temperature: CPU 86.4 °C / WL0 56.5 °C / WL1 54.3 °C
2 - E2000
dd-wrt.v24-30731_NEWD-2_K3.x_mega-e2000 (previous r30709)
Kernel: 3.10.103 #14437 Thu Oct 6 13:21:19 CEST 2016 mips DD-WRT
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok
Uptime: 45 minutes
CPU Temperature: WL0 53.3 °C
All devices working as AP's each with individual 1Gb wired connections to main firewall
Router : Netgear R7000
Firmware: DD-WRT v3.0-r30731 std (10/06/16)
Kernel: Linux 4.4.23 #1460 SMP Tue Oct 4 08:53:28 CEST 2016 armv7l
Status: Working
Reset: No
Previous: 30709
Errors: No
Router: Linksys E2000
Firmware: DD-WRT v3.0-r30731 mega (10/06/16)
Kernel: Linux 3.10.103 #14437 Thu Oct 6 13:21:19 CEST 2016 mips
Status: Working
Reset: YES, erase nvram after upgrade
Errors: None
With the previous build 30709 I wasn't able to configure BR1 from the GUI and the problem was fixed with this build. I did have to reboot the router to get changes to commit, but so far it's working.
Thanks BrainSlayer!! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Posted: Sat Oct 08, 2016 2:32 Post subject: Asus RT-AC68U
Router: Asus RT-AC68U
Firmware: DD-WRT v3.0-r30731 std (10/06/16)
Previous: DD-WRT v3.0-r30700M kongac (09/27/16)
Kernel: Linux 4.4.23 #1460 SMP Tue Oct 4 08:53:28 CEST 2016 armv7l
Previous: Linux 4.4.22 #128 SMP Tue Sep 27 22:44:00 CEST 2016 armv7l
Status: ok
Reset: yes (and then flashed via CFE)
Errors: Cannot Add a new bridge via GUI. GUI does not display all bridge parameters.
Operating Mode: Gateway
Uptime: 53 min
Temperature: CPU 78.0 °C / WL0 50.2 °C / WL1 52.7 °C
Router: D-Link DIR-895L
Firmware: DD-WRT v3.0-r30731 mega (10/06/16)
Kernel: 4.4.23 #1465 SMP Thu Oct 6 08:21:18 CEST 2016 armv7l
Status: LAN ports not working and wl2 not detected
Reset: Yes
Errors:
Initial flash from stock (stock firmware v1.12).
LAN/WAN ports don't work.
Tried pinging router's LAN IP with static IP on PC, no response.
Able to connect thru wl0.
Webgui shows wl0 and wl1 detected. No configuration available for wl2. _________________
Netgear R7800 kongpro 19.07 20190919 || Netgear R7000 36070M kongac (Client Bridge=5GHz, AP=2.4GHz with bridged VAP)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r30731 giga (10/06/16)
Previous: DD-WRT v3.0-r30471 giga (08/24/16)
Kernel: Linux 3.10.103 #14421 Thu Oct 6 13:07:31 CEST 2016 mips
Status: OK
Reset: Yes via GUI (Remember to backup & restore Status->WAN)
Errors: None
IPV6 DHCPv6 PD: Dead on cold start, OK after warm boot
WAN/LAN ports: OK
2.4GHz 40MHz N AP: OK
5GHz 40MHz AC/N AP: OK
ISP 30/6 bandwidth: 30/6
Site Survey: OK
Wiviz Survey: OK
OpenVPN Server: OK
USB Flash Drive: OK mounting /opt, /jffs, /swap partitions
Privoxy + Easylist: OK on /jffs
CPU Temperature: WL0 52.1°C, WL1 56.5°C _________________ [Broadcom] Asus rt-ac66u r35531 ('66 should only be factory reset through the DD UI)
Fix RT-AC66U "wl1 [2.4 GHz TurboQAM]". DD-WRT failsafe UI @ http|https://169.254.255.1/
Router: TrendNet TEW-811DRU
Firmware Version: DD-WRT v3.0-r30731 mini (10/06/16)
Kernel Version
Linux 4.4.23 #1463 Thu Oct 6 08:12:29 CEST 2016 armv7l
Status: Not Working
Reset: No
Previous: r29396
Errors: USB Drive will not mount. Status is noted as Not Mounted.
I went back to r29396. This is the last version that will allow usb drives for this model and I need this for YAMon3. This is reported in ticket 5467.
http://svn.dd-wrt.com/ticket/5467 _________________ Netgear R8000 - r50814 std - Main Router
Asus RT-AC68R -r46329 std - AP
Asus RT-AC68R -r46329 std - AP
TEW811DRU -r50595 mini - AP
TEW811DRU -r50595 mini - AP
Router: ASUS RT-N12 D1
Firmware: DD-WRT v3.0-r30731 mega (10/06/16)
Kernel: Linux 3.10.103 #14441 Thu Oct 6 13:24:48 CEST 2016 mips
Status: Working
Reset: YES
Errors:
In Status Panel the Wireless Signal is shown wrong.
(Wide HT40, Signal 11Mbit?; In Windows is 300Mbit shown). In Wide HT40 setting, by lower setup, the channel can't be selected.
Joined: 13 Aug 2013 Posts: 6866 Location: Romerike, Norway
Posted: Tue Oct 11, 2016 21:18 Post subject:
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r30731 giga (10/06/16)
Kernel: Linux 3.10.103 #14421 Thu Oct 6 13:07:31 CEST 2016 mips
Status: OK
Reset: NO
Errors: None
IP addresses are back in the Networking tab. They where blank in the previous 2 builds.
Router: Linksys EA6300v.1/EA6400
Firmware: v3.0-r30731 std (10/06/16)
Previous: v3.0-r30631 std (09/14/16)
Kernel: Linux 4.4.23 #1460 SMP Tue Oct 4 08:53:28 CEST 2016 armv7l
Status: Working
Reset: No
Errors: Same MAC for both radio (2.4/5Ghz), gpio 8 not working.
Uptime :11:13
In use as AP (2.4 Ghz bridged) and Repeater Bridge (5Ghz bridged)
CPU ModelBroadcom BCM4708
CPU Cores2
CPU Clock1200 MHz
CPU Temperature CPU 64.1 °C / WL0 45.1 °C / WL1 54.7 °C
Flashing on WebGui doesnt work.
Flashed using PuTTY to Telnet.
Code:
cd /tmp/root
mtd -f write linksys-ea6400-webflash.bin linux2
mtd -f write linksys-ea6400-webflash.bin linux
reboot
Posted: Wed Oct 12, 2016 16:27 Post subject: Linksys WRT 1200AC
PPTP server does not work in DD-WRT version 2016.
It can connect the PPTP server but it cannot browse the internet a long time
System
Router Name
Router Model
Linksys WRT 1200AC
Firmware Version
DD-WRT v3.0-r30731 std (10/07/16)
Kernel Version
Linux 3.18.42 #101 SMP Tue Oct 4 01:34:34 CEST 2016 armv7l
MAC Address
Hostname
WAN Domain Name
LAN Domain Name
Current Time
CPU
CPU Model
Marvel Armada 385
CPU Cores
2
CPU Clock
1332 MHz
Load Average
0%
0.00, 0.00, 0.00
CPU Temperature
CPU 0.0 °C / WL0 44.8 °C / WL1 46.6 °C
