Your reports for Qualcomm/Atheros units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Originally -- Linux 3.10.103 #168 Thu Sep 1 11:05:01 CEST 2016 mips
NEW -- Linux 3.10.103 #1174 Wed Sep 14 02:44:27 CEST 2016 mips
Status: GOOD (as far as I can tell - lol)
Reset: NO (kept settings and router rebooted normally as expected in any update)
Errors: None at this time.
Side note: Really wish the interface supported 4 dns (not just 3). ipv6 seems to only support 2 (while ipv4 3). But that's just me. lol I'm sure there is a reason that its 'as is'.
Netgear WNDR3700 V4
DD-WRT v3.0-r30631 std (09/14/16)
Linux 3.18.41 #826 Wed Sep 14 04:23:33 CEST 2016 mips
GUI install over 30605 - No Reset
All I use seems ok -
8 wireless devices did connect back after update. Some on ath0 - ath0.1 - ath1
No problems so far.
Just one ugly w/ath: phy0 I thought was a long-time-ago bug ¿
But only the 1 time thus far.
root@-----:~# dmesg | tail -5
<4>[ 60.470000] IMQ: autocreate imq1 NS 803b6410
<6>[ 60.470000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
<6>[ 60.480000] Hooking IMQ before NAT on PREROUTING.
<6>[ 60.480000] Hooking IMQ after NAT on POSTROUTING.
<3>[ 365.660000] ath: phy0: Could not kill baseband RX
root@-----:~# uptime
13:19:35 up 49 min, load average: 0.10, 0.05, 0.00
Also don't see DNSMasq size. I don't usually change it so it's always 1500.
Usually found >>> :~# /bin/ps | grep dnsmasq
but it don't say.
EDIT:
Last edited by mrjcd on Wed Sep 14, 2016 20:14; edited 1 time in total
Joined: 24 Feb 2013 Posts: 1634 Location: Belgrade
Posted: Wed Sep 14, 2016 19:33 Post subject:
Router Model GL.iNet-AR150
Firmware Version DD-WRT v3.0-r30631 std (09/14/16)
Kernel Version Linux 3.18.41 #842 Wed Sep 14 04:59:36 CEST 2016 mips
Status: working much better than OpenWRT :p
Reset: initial flash
Errors: None
@BS thx for supporting this little guy it is just awesome!!!
Router Model TP-Link TL-WR740N v4
Firmware Version DD-WRT v3.0-r30631 std (09/14/16)
Kernel Version Linux 3.10.103 #1216 Wed Sep 14 03:29:46 CEST 2016 mips
Status: ok
Reset: ok
Errors: None but CPU spikes to 2.5 after boot...
Appeared ok but connectivity on 2.4 was spotty. 2.4 is configured with Dynamic 20/40, NG-only, fixed channel 2 main, 6 secondary, 0 ack timing. This covers an 80' radius with zero interference from other access points. After some testing, ath0 (2.4 GHz) dropped completely. I noticed, as well, are reduced amount of activity on 2.4 than the prior build.
Back on r30385 until this radio issue can be resolved.
Router: TP-link wdr4300 v1.7
Firmware: DD-WRT v3.0-r30631 std (09/14/16)
Kernel: Linux 3.10.103 #1174 Wed Sep 14 02:44:27 CEST 2016 mips
Reset: factory to ddwrt and 30/30/30 reset
Bugs: susceptible reboots when I finish making configurations were about 4 or more reboots and use of heavy cpu after the restart only after 5 min back to normal, otherwise all ok
Router: TP-LINK TL-WR841ND v8
Firmware: v3.0-r30631 std (09/14/16)
Kernel: Linux 3.18.41 #800 Wed Sep 14 03:49:42 CEST 2016 mips
Status: OK
Reset: NO Reset, after setup reboot only
Errors: None so far, updated from Factory firmware, using in switch mode at work with Wifi and with Lan too.
Router: wzr-300hp
Firmware: Upgraded from 29739 to 30631
Kernel: Linux 3.10.103 #1154 Wed Sep 14 01:33:58 CEST 2016 mips
Status: OK
Reset: Yes both before and after update
Errors: wifi 2.4Gh drop after running about 40'
Edit: Wifi config same as the PeteSL do.
Last edited by sontt on Fri Sep 16, 2016 5:59; edited 1 time in total
Router: TPLINK WR1043ND V3
Firmware: DD-WRT v3.0-r30631 std (09/14/16)
Kernel: Linux 3.18.41 #810 Wed Sep 14 03:58:23 CEST 2016 mips
Status: Ok
Reset: NO
Errors: No
Is up for about 12 minutes and i think someone has done some good job here.
What i mean...first of all i have the last settings from the previous beta...so i will investigate farther to put the right settings...
First test in dsl reports...
I have 1Mbps for upload...with previous version i was suffering from upload lag spikes in QOS.
UPDATE
...............
I was just lucky in first dsl test...nothing change..it has the same terrible Qos in upload below 1Mbps connections.
I set upload etc at 800kbps and in test it starts at 1,14Mbps!!!!!!!!And then drops...lag spikes from 1ms to 700ms
Joined: 16 Nov 2015 Posts: 6411 Location: UK, London, just across the river..
Posted: Thu Sep 15, 2016 18:09 Post subject:
PeteSL wrote:
Buffalo WZR-600DHP
Upgraded from 30385 to 30631
Appeared ok but connectivity on 2.4 was spotty. 2.4 is configured with Dynamic 20/40, NG-only, fixed channel 2 main, 6 secondary, 0 ack timing. This covers an 80' radius with zero interference from other access points. After some testing, ath0 (2.4 GHz) dropped completely. I noticed, as well, are reduced amount of activity on 2.4 than the prior build.
Back on r30385 until this radio issue can be resolved.
Thanks for continuing development!
i guess your radio problems may originate from bad
radio settings.. better try full 40 or 20 only, Dynamic 20/40 has never been working well if you are concern, devices with 20HT will be able to connect even with 40HT selected only, as well ACK timing is broken too especially with 0 , also WPA2 AES wi-fi encryption is a must for a stable radio, i will recommend you short GI and Short preamble too, and try channel 11 + lower NG mixed is ok _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913