Oh, man! Your router is 32MB RAM (WDR3600 is 128MB). That makes a f*&¨%$uckn' difference, you're getting "out of memory".
In order to workaround it, maybe you should enable Swap partition, but I have NO idea how to do it.
EDIT: Rebooting router means to check whether all configuration are properly stored and working. If you're getting issues after rebooting that means something went wrong and all procedures should be repeated from scratch.
I don't think your router bad and WDR3600 is not any better either and thanx for removing those screenshots.
Ok I've run through your steps as I needed to update my broken implementation of Optware.
I'm having the following issue after copying the functions.sh over and going on to the next steps:
Code:
root@DD-WRT:/tmp# wget http://downloads.openwrt.org/snapshots/trunk/ar71xx/gener
ic/packages/base/uclibcxx_0.2.4-2_ar71xx.ipk
Connecting to downloads.openwrt.org (78.24.191.177:80)
uclibcxx_0.2.4-2_ar7 100% |*******************************| 70622 0:00:00 ETA
root@DD-WRT:/tmp# wget http://downloads.openwrt.org/snapshots/trunk/ar71xx/gener
ic/packages/base/libc_1.1.14-1_ar71xx.ipk
Connecting to downloads.openwrt.org (78.24.191.177:80)
libc_1.1.14-1_ar71xx 100% |*******************************| 268k 0:00:00 ETA
root@DD-WRT:/tmp# wget http://downloads.openwrt.org/snapshots/trunk/ar71xx/gener
ic/packages/base/opkg_9c97d5ecd795709c8584e972bfdf3aee3a5b846d-12_ar71xx.ipk
Connecting to downloads.openwrt.org (78.24.191.177:80)
opkg_9c97d5ecd795709 100% |*******************************| 55692 0:00:00 ETA
root@DD-WRT:/tmp# ipkg -d / -force-depends install uclibcxx_0.2.4-2_ar71xx.ipk
ERROR: File not found: //usr/local/lib/ipkg/lists/barrier_breaker
You probably want to run `ipkg update'
Unpacking uclibcxx...Done.
Configuring uclibcxx...grep: /usr/lib/opkg/info/uclibcxx.control: No such file or directory
cat: can't open '/usr/lib/opkg/info/uclibcxx.list': No such file or directory
Done.
Any help you can provide?
Also I reformatted the usb drive because when I tried it with 100mb (system) partition I got an Out Of Memory error.
doesn't execute.
It make my computer reset connection to router, and after reconnected (about 30s), my hdd was connected to router is empty (no folders was created, no files copied)
I'm using Buffalo WZR-300HP and dd-wrt r29621
Can anybody help?
Thanks in advanced and sorry for my bad English
Hi sontt, I would like to understand more details about your setup.
1. Which file did you flash to your router currently, is it buffalo_to_ddwrt_webflash-MULTI.bin or wzr-300hp-dd-wrt-webupgrade-MULTI.bin?
2. Which file format are you using for the USB drive: ext2/ext3/ext4/ntfs/fat32?
3. Have you check the File Permission and Attributes for the USB drive and make sure it is writable? You can do that by SSH to the router and enter command: ls -l /tmp/mnt
4. Can you write (upload) any file to /tmp/mnt/sda2 using WinSCP?
Hi sontt, I would like to understand more details about your setup.
1. Which file did you flash to your router currently, is it buffalo_to_ddwrt_webflash-MULTI.bin or wzr-300hp-dd-wrt-webupgrade-MULTI.bin?
2. Which file format are you using for the USB drive: ext2/ext3/ext4/ntfs/fat32?
3. Have you check the File Permission and Attributes for the USB drive and make sure it is writable? You can do that by SSH to the router and enter command: ls -l /tmp/mnt
4. Can you write (upload) any file to /tmp/mnt/sda2 using WinSCP?
Thanks for your reply.
I had fixed this problem. The main reason leading to errors due to my hard disk with bad sectors. After fix hard drive, everything work like a charm
Hi everyone,
I have problems with the open port for transmission. The transmission web interface said that port is closed.
My router which installed transmission is behind a internet modem. So I have to do the following:
-Internet modem: I forwarded port using on transmission to my router Lan IP.
-Router: I was added this commands to firewall to accept this port (Administrator>Command):
In the second part a of 1.1.2 i get the following errors in PuTTY:
Quote:
root@DD-WRT:/tmp# ipkg -d / -force-depends install uclibcxx_0.2.4-2_ar71xx.ipk
ERROR: File not found: //usr/local/lib/ipkg/lists/barrier_breaker
You probably want to run `ipkg update'
Unpacking uclibcxx...Done.
Configuring uclibcxx...grep: /usr/lib/opkg/info/uclibcxx.control: No such file or directory
cat: can't open '/usr/lib/opkg/info/uclibcxx.list': No such file or directory
Done.
root@DD-WRT:/tmp# ipkg -d / install libc_1.1.14-1_ar71xx.ipk
File not found libc_1.1.14-1_ar71xx.ipk
root@DD-WRT:/tmp# ipkg -d / install libc_1.1.15-1_ar71xx.ipk
ERROR: File not found: //usr/local/lib/ipkg/lists/barrier_breaker
You probably want to run `ipkg update'
Unpacking libc...Done.
Configuring libc...grep: /usr/lib/opkg/info/libc.control: No such file or directory
cat: can't open '/usr/lib/opkg/info/libc.list': No such file or directory
Done.
root@DD-WRT:/tmp# ipkg -d / install opkg_9c97d5ecd795709c8584e972bfdf3aee3a5b846
d-12_ar71xx.ipk
ERROR: File not found: //usr/local/lib/ipkg/lists/barrier_breaker
You probably want to run `ipkg update'
Unpacking opkg...Done.
Configuring opkg...grep: /usr/lib/opkg/info/opkg.control: No such file or directory
cat: can't open '/usr/lib/opkg/info/opkg.list': No such file or directory
Done.
Is there a way to overcome this? I have the Samba share up and running with windows and trying to get Transmission working. Tried various tutorials and this one looks the most promising so far. Thank you for reading!
You need to have /opt mounted on a USB drive or HDD.
then run the code:
Code:
wget -O - http://entware-3x.zyxmon.org/binaries/mips/installer/install_std.sh | sh
This will install Entware. Then you just need to run opkg update and opkg upgrade. Don't be worried about the missing packages. They don't seem to be needed, at least as far as I can see.
root@Farbwechsel ~ # opkg update
Error loading shared library libgcc_s.so.1: Exec format error (needed by /bin/opkg)
Error relocating /bin/opkg: __divsf3: symbol not found
Error relocating /bin/opkg: __floatunsisf: symbol not found
Error relocating /bin/opkg: __udivdi3: symbol not found
Error relocating /bin/opkg: __extendsfdf2: symbol not found
What am I doing wrong?
I'm trying to do this on a TPLINK WR1043ND V2 with DD-WRT v3.0-r30880