Linksys ea8500 port is ready

Post new topic   This topic is locked: you cannot edit posts or make replies.    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3 ... 17, 18, 19 ... 123, 124, 125  Next
Author Message
Wolf Kodi
DD-WRT User


Joined: 13 Jun 2010
Posts: 126

PostPosted: Thu Apr 07, 2016 12:47    Post subject: Reply with quote
Yes, I just confirmed that displaying ath1 crashes httpd and it doesn't show up in ps. I not using (and have never setup) WDS. This happens when my 5GHz radio is disabled, and it also happens when I set the channel width to 80MHz as I think that setting is effectively the same as disabling that radio because there is no signal output.

I disabled to my 5GHz radio to see if that stopped the ath10k_pci from mass spamming dmesg but it didn't.

_________________


YouTube | Facebook Page
Per-user Live Down/Upload Rate Monitoring [No PC needed!]
Sponsor
w32parite
DD-WRT Novice


Joined: 03 Jan 2012
Posts: 11

PostPosted: Thu Apr 07, 2016 16:35    Post subject: Reply with quote
hi....

when i type :
​http://x.x.x.x/Status_Router.asp

The gui works again.
I can make changes without issues.

After reboot webgui is gone....
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Sat Apr 09, 2016 0:26    Post subject: Reply with quote
check over this ticket, add any details to it that it may be missing. registering account there to post is free. http://svn.dd-wrt.com/ticket/5292
_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
niceiceman
DD-WRT Novice


Joined: 08 Sep 2007
Posts: 12

PostPosted: Sat Apr 09, 2016 4:46    Post subject: please help! Reply with quote
can someone please give me a hand? i think i have made a very silly mistake by loading
http://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2016/04-05-2016-r29409/linksys-ea8500/dd-wrt-webupgrade.bin
to my kong-build 29200 version..

since then, the router is dead and gets into an infinitive loop..

i cannot ping the router )request time out / destination host unreachable and hardware reset around 60's

what should I do now? the 30/30/30 method seems not working as well.
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Sat Apr 09, 2016 23:14    Post subject: Reply with quote
well that build works..dont know why it bricked. u can go from kong <-> brainslayer builds fine, i do it every time kong gives a new build just for checking if any issues are fixed there.

if it fails to boot it will try 3 times to boot then give up & load the fw on the other flash partition. how long did u let it boot loop for?

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
niceiceman
DD-WRT Novice


Joined: 08 Sep 2007
Posts: 12

PostPosted: Sun Apr 10, 2016 1:48    Post subject: Reply with quote
unfortunately.. it just keeps on infinitive looping for the whole day... i cannot either ping it or use tftp to flash any firmware to it....

i am 100% sure the upload of the firmware was completed as there was a screen pop up saying the upgrade was completed.
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Sun Apr 10, 2016 2:58    Post subject: Reply with quote
dont know then sorry. i havent fully bricked mine yet so i have no clue what the recovery procedure is, going to have to wait for kong to give u instructions. ill send him/her a message to check this thread.
_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Sun Apr 10, 2016 21:41    Post subject: Reply with quote
kong's response

It is pretty simple, setup a tftp server e.g. on 192.168.1.2, in the root dir of the tftp goes the firmware, run flashimg flashes to first part run flashimg2 to second part. Attach serial at boot just hit a key, then it jumps to uboot prompt where you set it up.


setenv image EA8500-factory-to-ddwrt.img
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
run flashimg

setenv image EA8500-factory-to-ddwrt.img
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
run flashimg2

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
niceiceman
DD-WRT Novice


Joined: 08 Sep 2007
Posts: 12

PostPosted: Tue Apr 12, 2016 2:18    Post subject: Reply with quote
does it mean i have to open the router and use serial recovery / jtag recovery? (and access through putty or hyper terminal?)
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Tue Apr 12, 2016 3:08    Post subject: Reply with quote
yes
_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7460
Location: YWG, Canada

PostPosted: Sun Apr 17, 2016 2:55    Post subject: Reply with quote
we dont need to double flash anymore, at least on bs builds. after unbricking from a broken nightly build i noticed that if boot_part is on 2, a single flash flashes both parts at once (even though on reboot itll still switch to part 1). but if boot_part is on 1, then u have to flash twice. flashing from boot_part 1 seems to do nothing, its like the flash never happened. once on 2, fw flashes to both in 1 try.

u can do ubootenv set boot_part 2 when its running, then flash a new build after it. no need to reboot after changing it.

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46412 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
[QUALCOMM] DIR-862L --------------------------------> r46395 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
kohmei
DD-WRT Novice


Joined: 06 Feb 2016
Posts: 30

PostPosted: Sun Apr 24, 2016 19:22    Post subject: Reply with quote
I got the .bin file off of Kong's site yesterday to update to 29510M. Today I noticed it's been updated again (24-Apr-2016 08:52) so I flashed that one. No matter what I do it stays at 29510M though. Not sure what's going on Confused
<Kong>
DD-WRT Guru


Joined: 15 Dec 2010
Posts: 4339
Location: Germany

PostPosted: Sun Apr 24, 2016 21:12    Post subject: Reply with quote
kohmei wrote:
I got the .bin file off of Kong's site yesterday to update to 29510M. Today I noticed it's been updated again (24-Apr-2016 08:52) so I flashed that one. No matter what I do it stays at 29510M though. Not sure what's going on Confused


The revision was not bumped, but added a little fix for the log spam.

_________________
KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
kohmei
DD-WRT Novice


Joined: 06 Feb 2016
Posts: 30

PostPosted: Sun Apr 24, 2016 22:59    Post subject: Reply with quote
<Kong> wrote:
kohmei wrote:
I got the .bin file off of Kong's site yesterday to update to 29510M. Today I noticed it's been updated again (24-Apr-2016 08:52) so I flashed that one. No matter what I do it stays at 29510M though. Not sure what's going on Confused


The revision was not bumped, but added a little fix for the log spam.

Thanks, I just noticed the build date is different Very Happy
thedak
DD-WRT Novice


Joined: 02 Nov 2010
Posts: 40

PostPosted: Mon Apr 25, 2016 0:09    Post subject: R7800? Reply with quote
Thanks Kong!! Any upcoming support or beta releases for the X4S R7800?
Goto page Previous  1, 2, 3 ... 17, 18, 19 ... 123, 124, 125  Next Display posts from previous:    Page 18 of 125
Post new topic   This topic is locked: you cannot edit posts or make replies.    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum