Support for: TP-LINK Model: TP-WA801ND

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3 ... 8, 9, 10, 11  Next
Author Message
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Tue Jan 12, 2016 14:53    Post subject: Reply with quote
GreyDoc wrote:
is your wa801nd v3 a US version? where did you bought it? please provide the exact model written on the label found on the router bottom. which stock firmware did you flash back to (version and link please)?


It should be a US version. I bought it in Greece. The original fw is a 4MB.

On the sticker:
Model: TL-WA801ND ver: 3.0
FCC ID: TE7WA801NDV3

I tried to modify and flash this release: ftp://ftp.dd-wrt.com/betas/2016/01-02-2016-r28647/tplink_tl-wr841ndv10/ The "factory-to-ddwrt.bin" image.

The (working) stock fw I flashed back using tftp (LAN IP 192.168.0.66 MASK: 255.255.255.0 Gateway: blank) is this: http://www.tp-link.com/res/down/soft/TL-WA801ND_V3_150723.zip from this page: http://www.tp-link.com/en/download/TL-WA801ND.html#Firmware

I attached it in case somebody needs it. I've discarded the "boot" part (first 257 bytes).


Last edited by understracker on Tue Jan 12, 2016 22:04; edited 7 times in total
Sponsor
GreyDoc
DD-WRT User


Joined: 04 Jun 2015
Posts: 392

PostPosted: Tue Jan 12, 2016 15:43    Post subject: Reply with quote
try attached file for the WA801NDv3 (modified WR841NDv10 build)

Last edited by GreyDoc on Tue Jan 12, 2016 17:06; edited 1 time in total
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Tue Jan 12, 2016 15:56    Post subject: Reply with quote
GreyDoc wrote:
try attached file for the WA801NDv3 (modified WR841NDv10 build)


Nuh it doesn't work. It does the same thing: Boot -> eth led light up for 10 sec -> reboot and so on. I tried to access the stock fw through ssh to get some info but I get "Server refused to allocate pty" error. It doesn't seem to respond to telnet, either. The thing is that I don't have a serial cable to do serial debug.
GreyDoc
DD-WRT User


Joined: 04 Jun 2015
Posts: 392

PostPosted: Tue Jan 12, 2016 16:19    Post subject: Reply with quote
try attached file for the WA801NDv3 US version (modified WR841NDv10 build)

Last edited by GreyDoc on Tue Jan 12, 2016 17:05; edited 1 time in total
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Tue Jan 12, 2016 16:29    Post subject: Reply with quote
GreyDoc wrote:
try attached file for the WA801NDv3 US version (modified WR841NDv10 build)


It reboots forever as before. It looks like a kernel panic.
GreyDoc
DD-WRT User


Joined: 04 Jun 2015
Posts: 392

PostPosted: Tue Jan 12, 2016 16:39    Post subject: Reply with quote
last try for WA801NDv3 (modified WR841NDv9 build)

Last edited by GreyDoc on Tue Jan 12, 2016 17:06; edited 1 time in total
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Tue Jan 12, 2016 16:57    Post subject: Reply with quote
GreyDoc wrote:
last try for WA801NDv3 (modified WR841NDv9 build)


It doesn't work either.... Sad Anyway, thanks for your help.
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Wed Jan 20, 2016 18:51    Post subject: More findings Reply with quote
WA801NDv3 does work as WR802Nv1 using this stock firmware (after discarding "boot" part and header modification). However it doesn't work with modified TL-WR841ND v9 firmware as WR802Nv1 does according to this thread.
GreyDoc
DD-WRT User


Joined: 04 Jun 2015
Posts: 392

PostPosted: Wed Jan 20, 2016 20:32    Post subject: Reply with quote
maybe it's a size problem.. try this v9 build r24160 with header changed for wa801ndv3

Last edited by GreyDoc on Thu Jan 21, 2016 19:32; edited 1 time in total
understracker
DD-WRT Novice


Joined: 28 Oct 2014
Posts: 48

PostPosted: Thu Jan 21, 2016 17:25    Post subject: Reply with quote
GreyDoc wrote:
maybe it's a size problem.. try this v9 build r24160 with header changed for wa801ndv3

It doesn't work. It seems to boot properly (power & ethernet led light up) until something happens and restarts. I have ordered a USB to TTL serial cable from china. When it arrives I'll post more information.
jaspras
DD-WRT Novice


Joined: 05 Sep 2013
Posts: 6

PostPosted: Wed Mar 09, 2016 12:28    Post subject: Reply with quote
THIS IS 801nd Version 3 boot with dd-wrt for 841nd v10


U-Boot 1.1.4 (Jul 23 2015 - 17:09:2Cool

ap143-2.0 - Honey Bee 2.0

DRAM: 32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash: 4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4081a100
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.18.27 (root@nmndev) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r48830) ) #9446 Wed Mar 2 03:51:27 CET 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] cpu apb ddr apb cpu 650 ddr 391 ahb 216
QCA9533 V2

detect mem size

Uart Init

Booting WASP !!! -Smile ...

[ 0.000000] sys id = 160 Qualcomm Atheros QCA9533 ver 2 rev 1.0 (0x0160)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28896K/32768K available (2268K kernel code, 149K rwdata, 204K rodata, 184K init, 340K bss, 3872K reserved)
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] NET: Registered protocol family 16
[ 0.490000] Switched to clocksource MIPS
[ 0.500000] NET: Registered protocol family 2
[ 0.500000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.500000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.510000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.510000] TCP: reno registered
[ 0.520000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.520000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.530000] NET: Registered protocol family 1
[ 0.530000] gpio_proc: module loaded and /proc/gpio/ created
[ 0.540000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[ 0.550000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.560000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.560000] msgmni has been set to 56
[ 0.570000] io scheduler noop registered (default)
[ 0.570000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.580000] console [ttyS0] disabled
ϊ[ 0.600000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.610000] console [ttyS0] enabled
[ 0.610000] console [ttyS0] enabled
[ 0.620000] bootconsole [early0] disabled
[ 0.620000] bootconsole [early0] disabled
[ 0.620000] guessed flashsize = 4M
[ 0.630000] scanning for root partition
[ 0.630000] tplink uboot detected
[ 0.640000] guessed bootloader size = 20000
[ 0.650000]
[ 0.650000] found squashfs at 110000
[ 0.660000] adjusted length 3D0000, original length 3CC70E
[ 0.660000] Creating 9 MTD partitions on "ar7240-nor0":
[ 0.670000] 0x000000000000-0x000000020000 : "RedBoot"
[ 0.670000] 0x000000020000-0x0000003e0000 : "linux"
[ 0.680000] 0x000000110000-0x0000003d0000 : "rootfs"
[ 0.690000] mtd: partition "rootfs" set to be root filesystem
[ 0.690000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
[ 0.700000] 0x0000003e0000-0x0000003f0000 : "nvram"
[ 0.700000] 0x0000003f0000-0x000000400000 : "board_config"
[ 0.710000] 0x000000000000-0x000000400000 : "fullflash"
[ 0.720000] 0x000000000000-0x000000020000 : "fullboot"
[ 0.720000] 0x000000010000-0x000000020000 : "uboot-env"
[ 0.730000] libphy: Fixed MDIO Bus: probed
[ 0.730000] tun: Universal TUN/TAP device driver, 1.6
[ 0.740000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.740000] PPP generic driver version 2.4.2
[ 0.750000] PPP BSD Compression module registered
[ 0.750000] PPP Deflate Compression module registered
[ 0.760000] PPP MPPE Compression module registered
[ 0.760000] NET: Registered protocol family 24
[ 0.770000] u32 classifier
[ 0.780000] Performance counters on
[ 0.780000] input device check on
[ 0.780000] Actions configured
[ 0.790000] Netfilter messages via NETLINK v0.30.
[ 0.790000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
[ 0.800000] nf_conntrack_rtsp v0.6.21 loading
[ 0.800000] nf_nat_rtsp v0.6.21 loading
[ 0.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.810000] TCP: westwood registered
[ 0.820000] TCP: hybla registered
[ 0.820000] TCP: vegas registered
[ 0.820000] NET: Registered protocol family 17
[ 0.830000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.840000] Bridge firewalling registered
[ 0.850000] 8021q: 802.1Q VLAN Support v1.8
[ 0.870000] searching for nvram
[ 0.870000] nvram size = 0
[ 0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
[ 0.910000] ar71xx-wdt: timeout=15 secs (max=171) ref freq=25000000
[ 0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.930000] Freeing unused kernel memory: 184K (802f2000 - 80320000)
start service
starting Architecture code for dir615e
udevtrigger[255]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
load ATH Ethernet Driver
[ 2.840000] libphy: ag71xx_mdio: probed
[ 3.430000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 3.490000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 4.160000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 4.170000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Failed to connect to the switch. Use the "list" command to see which switches are available.
Failed to connect to the switch. Use the "list" command to see which switches are available.
Failed to connect to the switch. Use the "list" command to see which switches are available.
Failed to connect to the switch. Use the "list" command to see which switches are available.
load ATH 802.11 a/b/g Driver
load ATH9K 802.11n Driver
[ 4.410000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 4.420000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 4.980000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=2
ath9k deconfigure_single: phy0 ath0
[ 7.150000] device br0 entered promiscuous mode
[ 7.340000] device eth0 entered promiscuous mode
[ 7.350000] device br0 left promiscuous mode
[ 7.360000] device br0 entered promiscuous mode
[ 7.380000] device br0 left promiscuous mode
ath9k deconfigure_single: phy0 ath0

resetbutton: factory default.
send dhcp lease release signal
Sending SIGTERM [ 12.070000] ar71xx-wdt: device closed unexpectedly, watchdog timer will not stop!
to all processes
Sending SIGKILL to all processes
unmounting /
unmounting /
[ 20.110000] reboot: Restarting system
jaspras
DD-WRT Novice


Joined: 05 Sep 2013
Posts: 6

PostPosted: Thu Mar 10, 2016 11:05    Post subject: Reply with quote
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4081a100
is_auto_upload_firmware=0
Autobooting in 1 seconds



i forgot to post this
compact72
DD-WRT Novice


Joined: 23 May 2016
Posts: 1

PostPosted: Mon May 23, 2016 3:51    Post subject: Reply with quote
has anybody got this working for TL-WA801ND v3 yet?
KrypteX
DD-WRT Guru


Joined: 18 Jan 2014
Posts: 2411

PostPosted: Tue May 31, 2016 19:06    Post subject: Reply with quote
compact72 wrote:
has anybody got this working for TL-WA801ND v3 yet?

Here: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=989951#989951

_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX

Testing BrainSlayer's DD-WRT build 31924 on various units:
NETGEAR : WNDR3800 WNDR3800CH WNDRMACv2 WNDRMACv1 WNR2200 WNR2000v3
TP-LINK : ArcherC7v3 WR1043NDv3 WR740Nv4 WR740Nv6 WR710Nv1 WR810Nv1 WA850REv1 WA901NDv3 WA901NDv4
D-LINK : DIR-862L DIR-615D2
ASUS : RT-N10 C1
VirtualBox : x86_64
jaspras
DD-WRT Novice


Joined: 05 Sep 2013
Posts: 6

PostPosted: Thu Jun 09, 2016 19:16    Post subject: Reply with quote
KrypteX wrote:
compact72 wrote:
has anybody got this working for TL-WA801ND v3 yet?

Here: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=989951#989951





nop! constant reboots...
Goto page Previous  1, 2, 3 ... 8, 9, 10, 11  Next Display posts from previous:    Page 9 of 11
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum