Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28882_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Router: TP-Link Archer C8 v1
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #150 SMP Tue Jan 19 06:04:41 CET 2016 armv7l
Status: Okay
Reset: No
Errors: None so far
This build seems to have fixed the wireless drop-outs faced in the previous two builds.
Router: Asus RT-AC68U
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #150 SMP Tue Jan 19 06:04:41 CET 2016 armv7l
Status: Okay
Reset: No
Errors: None so far
Upgraded without reset from 28846.
Wifi clients seem to connect faster and no dropping out of the 2.4hgz signal. _________________ Location (urban) - 1x Linksys EA8500 (AP wlan0 & wlan1 enabled)
1x Asus 68u (Repeater Bridge w/VAP) - wl0 disabled
1x Asus 87u (Client Bridge) - wl1 disabled
Router: Netgear R7000
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #148 SMP Mon Jan 18 06:12:48 CET 2016 armv7l
Status: Working
Reset: No
Previous: 28846
Errors: No
Router: Netgear R7000
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #148 SMP Mon Jan 18 06:12:48 CET 2016 armv7l
Status: Working fine
Reset: No Reset (upgrading from r28788)
Errors: No errors... but still Gigabit LAN speed issue
Little improvement on my Gigabit LAN speed issue:
- now it goes around 70MB/s but not beyond
- better than 60MB/s with r28788
- still very far from the 90-100MB/s with r25974 (that I've been using over the last year)
Correction: after some other tests, it does seem to start at 100MB/s but quickly slows down towards 70MB/s.
Last edited by fredberr on Tue Jan 19, 2016 19:16; edited 1 time in total
Router: Linsys EA6300 v1 (EA6400 )
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #148 SMP Mon Jan 18 06:12:48 CET 2016 armv7l
Status: Working with malfunctions
Reset: No Reset (upgrading from r28493)
Errors: 1. Wifi clients dropped out on 2.4ghz.
2. Shows wrong extension channel on 2.4ghz (e.g 7+9 or 9+11)
Router: Netgear R7000
Errors: No errors... but still Gigabit LAN speed issue
Little improvement on my Gigabit LAN speed issue:
- now it goes around 70MB/s but not beyond
- better than 60MB/s with r28788
- still very far from the 90-100MB/s with r25974 (that I've been using over the last year)
Correction: after some other tests, it does seem to start at 100MB/s but quickly slows down towards 70MB/s.
How are you testing the LAN speed? _________________ Segment 1 XR700 10Gb LAN, 1Gb WAN ISP BS
Wired AP 1 Unifi Wifi 6 LR US 1Gb LAN
Wired AP 2 Unifi Wifi 6 LR US 1Gb LAN
Wired AP 3 Unifi Wifi 6 LR US 1Gb LAN
Syslog Services Asustor 7110T NAS 10GB
NetGear XS716T 10GB Switch
download1.dd-wrt.com/dd-wrtv2/downloads/betas/ (Brain Slayer)
YAMon https://usage-monitoring.com/index.php
Joined: 14 Oct 2006 Posts: 296 Location: Sector 001
Posted: Tue Jan 19, 2016 21:49 Post subject:
Router: Netgear WNDR4500v2
Firmware: DD-WRT v3.0-r28882 Giga (01/19/16)
Kernel: Linux 3.10.94 #11127 Tue Jan 19 09:18:59 2016 mips
Status: OK so far
Reset: Yes
Errors: None yet
First time flashing this model to DD-WRT and noted 2 things while configuring it.
1. When disabling the 5GHZ radio, the LED stays on. Confirmed radio is off but LED illuminates. Rebooted, no change. 2.4GHZ LED goes off after disabling.
2. When selecting Wide HT40 Channel Width in 2.4GHZ radio, channel changes to "Auto" after save. Drop down has no other options but "Auto". Click Save a 2nd time and then channels 5-11 show up. What happened to 1-4? HT20 has all the channels available in the drop down.
Update:
2. Guess this is normal depending if upper or lower is selected.
3. Front LEDs work but they do not show any activity flashing at all. They all stay solid on.
Last edited by phlegmer on Wed Jan 20, 2016 14:20; edited 2 times in total
Router: Netgear R7000
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux core 4.4.0 #148 SMP Mon Jan 18 06:12:48 CET 2016 armv7l DD-WRT
Status: OK
Reset: No
Errors: USB flash drive not showing up on USB.asp page, shows as "Not available" under Disk Info. Was working on r28647.
Edit: Reset to defaults on 28882 and USB was still not working. Restored to 28647 and USB is functioning normally.
Last edited by reznap on Wed Jan 20, 2016 0:32; edited 1 time in total
Router: Asus RT-AC87U
Firmware: DD-WRT v3.0-r28882 std (01/19/16)
Kernel: Linux 4.4.0 #150 SMP Tue Jan 19 06:04:41 CET 2016 armv7l
Status: Okay
Reset: No
Errors: None so far
Upgraded without reset from 28846 over the WAN _________________ Location (urban) - 1x Linksys EA8500 (AP wlan0 & wlan1 enabled)
1x Asus 68u (Repeater Bridge w/VAP) - wl0 disabled
1x Asus 87u (Client Bridge) - wl1 disabled
Router: Linksys E1200 v2
Firmware: DD-WRT v3.0-r28882 mini (01/19/16)
Kernel: Linux 2.6.24.111 #28262 Tue Jan 19 01:14:12 CET 2016 mips
Status: Working
Reset: Yes
