Search found 13 matches

Author Message
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Fri Nov 28, 2014 16:40   Subject: control + c
Nikopol2014 , if u cand see the mesages u showed my in your log, the parameters in putty are ok,otherway u could not see nothing there. putty had to be open, prepared before u power on the router.The ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Oct 20, 2014 21:59   Subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command ...
  Topic: Tenda W306R serial flashing - help identify TX / RX points
reluare

Replies: 10
Views: 14494

PostForum: Ralink SoC based Hardware   Posted: Fri Sep 27, 2013 12:51   Subject: Tenda W306R serial flashing - help identify TX / RX points
Hello, I have two routers w306r model with the same problem. Appear start normally, but after a few seconds of starting remain lit only "power", "WLAN" and "SYS". If I co ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Sep 16, 2013 10:12   Subject: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?
The circuit can be easily destroyed if you use a soldering iron ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Sat Sep 14, 2013 9:25   Subject: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?
The circuit can be easily destroyed if you use a soldering iron ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Fri Sep 13, 2013 22:02   Subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Fri Sep 13, 2013 15:24   Subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Wed Sep 11, 2013 21:27   Subject: TendaW311R+ rx tx broadcom chipset , board v 2.0
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Sep 09, 2013 18:31   Subject: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
I DID IT !!!
Very Happy
Boot sequence stops with the command Ctrl + C, at which the router begins to respond to ping. I then tried to use a TFTP server to upload the firmware but it did not work. Trying ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Sep 09, 2013 15:47   Subject: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
Post was complete, I waited 10 minutes and never showed anything but what I wrote above, then I tried to start with the reset button pressed, the only difference was that I showed at one time message ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Sep 09, 2013 15:19   Subject: TendaW311R + hardware version 2.0 broadcom chipset
I found the two points, rx and tx were marked with TP1 and TP 2, I connected a USB-UART from a nokia 6030, I opened putty and I powered the router. I received the following message

"Decompress ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Mon Sep 02, 2013 18:12   Subject: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
Look at the pics at first post of the thread. Then read through it about the recovery methods.

Also, note diferences between 311R and 311R+ firmwares. You need to download the correct one for your ...
  Topic: TENDA W311R - Bad flash recover and Install dd-wrt firmware!
reluare

Replies: 333
Views: 476555

PostForum: Ralink SoC based Hardware   Posted: Sun Sep 01, 2013 14:06   Subject: TendaW311R +
Hi, I'm the owner of a TendaW311R + router that does not work. I need to tell me if you can and if you know which points tx and rx where I can connect a TTL converter and reinstate him. I attach a pic ...
All times are GMT
Navigation
Jump to: