Search found 18 matches

Goto page 1, 2  Next
Goto page 1, 2  Next
Author Message
  Topic: D-Link DIR-615
mrrhtuner

Replies: 452
Views: 1152297

PostForum: Atheros WiSOC based Hardware   Posted: Wed Mar 08, 2017 2:36   Subject: D-Link DIR-615
Sorry for the super old bump but I figure it's better to bump the existing thread than start a new one.

We have a Dlink DIR-615 C1 using Stock 3.11 firmware.

I've followed the guides and was abl ...
  Topic: Looking to hackup my e4200...antenna mod first!
mrrhtuner

Replies: 3
Views: 5799

PostForum: Hardware DIY / Hardware Mods   Posted: Wed Jan 25, 2017 20:57   Subject: Looking to hackup my e4200...antenna mod first!
Hey guys, I've purchased a TP-Link Archer C7 and thinking it would be a huge improvement over my Linksys E4200v1...it doesn't feel like it.

The range due to the external antenna's on the Archer C7 ...
  Topic: WNR2000V1 Antenna Connector
mrrhtuner

Replies: 2
Views: 5076

PostForum: Hardware DIY / Hardware Mods   Posted: Wed Jan 25, 2017 20:49   Subject: WNR2000V1 Antenna Connector
That looks like U.Fl cables could work there.

Search U.Fl cables and see if anybody else has used them on your router.
  Topic: Linksys wrt310n owners come in, question about client bridge
mrrhtuner

Replies: 1
Views: 2739

PostForum: Broadcom SoC based Hardware   Posted: Sun Nov 06, 2011 15:49   Subject: Linksys wrt310n owners come in, question about client bridge
Hello everybody, so I've been on a mission to share my internet from my primary router to my linksys wrt310n V2.

I have had some guidence in the following thread on configuring the WRT310n to act a ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 3:14   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Good, so the client bridge works. Hopefully it's reliable.

Sorry, my message was cut off.

I was writing the post above at the time and once again the connection dropped.

Would you know if the ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 2:33   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
So after having the Sony unplugged from the router, I hooked it back up via ethernet(wireless disabled) and its back online(I'm writing this on it).

I am getting a 192.168.2.xx IP, proper subnet an ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 2:06   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
I have no idea. Now you're introducing multiple computers, varying ports and leds, etc. No way for me to follow that much complexity from here. All I can address is how to get ONE computer working ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 1:38   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
So here is what I've realized.

I am using a Dell m1530 laptop, whenver I plug into the router via ethernet it pretty much drops the internet connection.

If I have my other Sony Vaio laptop conne ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 1:00   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Yes I figured that, thank you.

The encryption is set to WEP(same as my primary router)

Any suggestions on what I should look at? I'm not going to move onto the 'wireless repeater' and do the sam ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Sun Nov 06, 2011 0:26   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Hey sorry for the delay. Had to take my network due to apartment renovations.

To my previous issue, I had it working before but only for a short period of time. Today I reset the DDWRT settings a ...
  Topic: WRT310n V2 DDWRT firmware install....some questions
mrrhtuner

Replies: 7
Views: 11544

PostForum: Broadcom SoC based Hardware   Posted: Tue Oct 25, 2011 21:04   Subject: WRT310n V2 DDWRT firmware install....some questions
Yea I had applied the std_nokiad_small but then I was told it might be unstable to use so I reverted to mini.

Wheather that is correct or not, I'm not sure
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Tue Oct 25, 2011 12:53   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Well after following the guide and doing some figuring out, I got the bridge to work.
There is a problem though with the connection. For some reason it got a connection last night then it seems like ...
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Tue Oct 25, 2011 2:58   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Thank you very much eibgrad

I will give it a shot in a bit and see how it works out.
  Topic: Setting up bridged network with Bell 2701HG-G Gateway modem
mrrhtuner

Replies: 8
Views: 12541

PostForum: Advanced Networking   Posted: Tue Oct 25, 2011 2:08   Subject: Setting up bridged network with Bell 2701HG-G Gateway modem
Hey everybody, I have started reading the DDWRT documents for bridging networks and within the wiki pages it seems that they use 3rd party router hardware(2 linksys routers, netgear, so on) but not an ...
  Topic: WRT310n V2 DDWRT firmware install....some questions
mrrhtuner

Replies: 7
Views: 11544

PostForum: Broadcom SoC based Hardware   Posted: Mon Oct 24, 2011 13:41   Subject: WRT310n V2 DDWRT firmware install....some questions
If you read note 4 carefully, you will see there is a link to "file versions" that explains the difference between each file type. Obviously you don't want a generic USB build if you don't ...
All times are GMT
Navigation
Jump to: