Search found 1102 matches

Goto page 1, 2, 3 ... 72, 73, 74  Next
Author Message
  Topic: Netgear WNR3500L V2 DD-WRT V3 OpenVPN illegal instruction
eibgrad

Replies: 6
Views: 1517

PostForum: Advanced Networking   Posted: Tue Sep 20, 2022 17:44   Subject: Netgear WNR3500L V2 DD-WRT V3 OpenVPN illegal instruction
The OP specifically mentions that he's running two OpenVPN instances. Since the GUI only suppprts *one*, I have to assume either a) one is running w/ the GUI, the other via a script, or b) both are r ...
  Topic: [Solved]Not all traffic goes through VPN Client on DD-WRT AP
eibgrad

Replies: 7
Views: 1565

PostForum: Advanced Networking   Posted: Thu Sep 15, 2022 17:52   Subject: [Solved]Not all traffic goes through VPN Client on DD-WRT AP
I had to reread this post several times to be sure I understood the fundamental problem here. And even so, I'm still not so sure I do.

First, when it comes to Gateway vs. Router mode w/ DD-WRT, th ...
  Topic: Possible causes for WG bandwidth only 65% of OpenVPN?
eibgrad

Replies: 6
Views: 1327

PostForum: Advanced Networking   Posted: Wed Sep 14, 2022 5:59   Subject: Possible causes for WG bandwidth only 65% of OpenVPN?
If possible, I would try using the router's WG client w/ a commercial VPN provider just to see if the performance improves significantly when connected to something other than your own WG server. If ...
  Topic: Iptables to allow internet but not lan
eibgrad

Replies: 4
Views: 675

PostForum: Advanced Networking   Posted: Sun Sep 04, 2022 17:36   Subject: Iptables to allow internet but not lan
The lack of information about the guest router makes it difficult to provide accurate advice. What's the make and model? Does it support DD-WRT? Are you using DD-WRT? Is the WAN NAT'd?

Typicall ...
  Topic: Static Routing not working Firmware: DD-WRT v3.0-r49467 N66u
eibgrad

Replies: 4
Views: 614

PostForum: Advanced Networking   Posted: Mon Aug 29, 2022 1:09   Subject: Static Routing not working Firmware: DD-WRT v3.0-r49467 N66u
I don't agree that you can accurately assess if the static route is being used based on the timing. That's far too speculative. There may be other factors at play here.

A common mistake in this ca ...
  Topic: openvpn not picking up client specdific options from correct
eibgrad

Replies: 6
Views: 896

PostForum: Advanced Networking   Posted: Fri Aug 26, 2022 20:44   Subject: openvpn not picking up client specdific options from correct
Looks to me like it *is* picking up the iroute. You posted a snapshot of the syslog rather than the actual syslog, so it makes it harder to point it out. But there is a line @ 17:22:19 (second to la ...
  Topic: Static leases for same device using both LAN and VPN
eibgrad

Replies: 8
Views: 1062

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 20:20   Subject: Static leases for same device using both LAN and VPN
Well, it seems like adding the following two lines works:
server 10.10.10.0 255.255.255.0 nopool
ifconfig-pool 10.10.10.50 10.10.10.75


The first line supersedes the default line (and correspond ...
  Topic: openvpn not picking up client specdific options from correct
eibgrad

Replies: 6
Views: 896

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 19:22   Subject: openvpn not picking up client specdific options from correct
If you have JFFS enabled, the OpenVPN server looks in /jffs/etc/openvpn/ccd for client-specific files, NOT /tmp/openvpn/ccd.

Also, it appears you have other issues. The syslog indicates the server ...
  Topic: Static leases for same device using both LAN and VPN
eibgrad

Replies: 8
Views: 1062

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 18:35   Subject: Static leases for same device using both LAN and VPN

Beware! Unlike DHCP and static leases, OpenVPN will ***NOT*** reserve these IP assignments! IOW, if a client comes along that's NOT configured w/ one of these static IP assignments, it gets assigne ...
  Topic: Static leases for same device using both LAN and VPN
eibgrad

Replies: 8
Views: 1062

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 18:31   Subject: Static leases for same device using both LAN and VPN
What value should be used for the netmask?

Whatever you've chose for the subnet mask on the OpenVPN server.

The article you referenced talks about "Server IP Endpoints" and "succe ...
  Topic: [SOLVED]WG Setting "Allow Clients Full LAN Access"
eibgrad

Replies: 27
Views: 3922

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 3:51   Subject: [SOLVED]WG Setting "Allow Clients Full LAN Access"
"Bypass LAN Same-Origin Policy" is a sound label name, I must have missed your original mention.

I can change it on my next PR

Re: documentation (I mean DD-WRT built in help pages/text ...
  Topic: Static leases for same device using both LAN and VPN
eibgrad

Replies: 8
Views: 1062

PostForum: Advanced Networking   Posted: Thu Aug 25, 2022 0:01   Subject: Static leases for same device using both LAN and VPN
If you want to have static IP assignments w/ OpenVPN, there's a specific set of steps that are required.

Each client, uniquely identified by its CN (Common Name) on its client cert, has to have a f ...
  Topic: Access to statis host ip addresses from VPN
eibgrad

Replies: 7
Views: 827

PostForum: Advanced Networking   Posted: Wed Aug 24, 2022 5:41   Subject: Access to statis host ip addresses from VPN
Are using the fully-qualified hostname? (e.g., hostname.mydomain)

Might be a good idea to add the following directive as well.

expand-hosts

That should let you reference unqualified names in ...
  Topic: Access to statis host ip addresses from VPN
eibgrad

Replies: 7
Views: 827

PostForum: Advanced Networking   Posted: Wed Aug 24, 2022 5:09   Subject: Access to statis host ip addresses from VPN
You have to add the VPN's network interface (tun2) to DNSMasq so that it will listen on it.

Under Services > Additional DNSMasq Options, add the following.

interface=tun2
  Topic: [Solved] Ad Blocking for "dummies".
eibgrad

Replies: 21
Views: 7481

PostForum: General Questions   Posted: Tue Aug 23, 2022 1:14   Subject: [Solved] Ad Blocking for "dummies".
In the Begin/End Options section, there are three (3) of them, including the ability to add/remove URLs, domains you might want to whitelist, and the ability to change the timeout on the curl command.
Goto page 1, 2, 3 ... 72, 73, 74  Next
All times are GMT
Navigation
Jump to: