Author | Message |
---|---|
![]() |
|
cmaas Replies: 3 Views: 2465 |
![]() |
I noticed what you say about the GUI and what rate it shows. I should have explained better of the testing I did, sorry. What I am getting is seeing a 54mb connection on each client that has N cap ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 2465 |
![]() |
I have been using this E2000 as a basic access point and at first I would be able to connect a N client and see those speeds. After a month or so, I now can only get G speeds. And if I switch the ... |
|
![]() |
|
![]() |
|
cmaas Replies: 2 Views: 2660 |
![]() |
I'm assuming you mean Virtual Access Point. Yes? Is this the same as a virtual interface? I don't see anything for vap. | |
![]() |
|
![]() |
|
cmaas Replies: 2 Views: 2660 |
![]() |
How can you make a virtual interface that uses a different security password. I do understand that in order to make the "repeater" in the Repeater/Bridge, you need a virtual interface tha ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 2382 |
![]() |
Sorry for the delay. If you want to clone your MAC address, go to the SETUP tab and then to the MAC ADDRESS CLONE tab. One your there, it's self explanatory on how to complete this. it actually wil ... | |
![]() |
|
![]() |
|
cmaas Replies: 1 Views: 2110 |
![]() |
Router: WRT54GL ver1.1 Firmware: DD-WRT v24-sp2 (10/10/09) std - build 13064 Setup: Basic Gateway I have searched around and haven't seen much info on the Wi-Viz. It sounds like a cool idea but ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 2382 |
![]() |
I may not have the perfect answer for you (still learning DD-WRT myself) But a few ideas. The free wi-fi login page issue. Do your login with your laptop and then clone your laptop's MAC into your ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 3154 |
![]() |
I had the same problem before with my first VPN/DD-WRT project. Now I found the solution than and stupid me I did not document the problem. I now just copy settings from my home router when I set up ... | |
![]() |
|
![]() |
|
cmaas Replies: 6 Views: 5522 |
![]() |
I'd definitely try to use a higher quality cable and shorter if possible. Forgive me all but there is a link somebody gave me to a great thread on antennas. In operation, I have seen the donut ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 3268 |
![]() |
To your last comment, If you use your router in repeater/bridge, the bandwidth you get on a client will be 1/2 (from what I've been hearing). So for gaming, I would think that setup wouldn't be the g ... | |
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 2984 |
![]() |
Sorry, what I was trying to ask was currently they are both set to Auto and if making one unit use the external ant to Tx and the other one to RX would be better. Basically, do I need to use both an ... |
|
![]() |
|
![]() |
|
cmaas Replies: 9 Views: 30443 |
![]() |
Love that picture...haha What are the performance gains from over clocking the CPU's? I only have been working with WRT54G (2)(L)'s Some are routers, access points, and repeater/bridges. I ha ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 1819 |
![]() |
I swapped in the G2 and the CPU load dropped down to <10% I thought everything was fine but the DHCP was horribly slow. Enough so that some of my clients would timeout. I was getting unhappy ... |
|
![]() |
|
![]() |
|
cmaas Replies: 3 Views: 2984 |
![]() |
Access Point - WRT54GL w/ single 10dbi Omni-directional ant. Repeater/Bridge - WRT54GL w/ single 10dbi Omni-directional ant. What would be the optimum settings in the Advanced Settings? The se ... |
|
![]() |
|
![]() |
|
cmaas Replies: 18 Views: 13410 |
![]() |
I think everybody gave up on me :( But the project is finished and the customer is thrilled. I am getting a 52% signal and average ping times from the start point to the far machine is around 10 ... |
|
![]() |
|
All times are GMT |