Search found 7640 matches

Goto page 1, 2, 3 ... 508, 509, 510  Next
Author Message
  Topic: Netgear wrt3500
LOM

Replies: 7
Views: 1151

PostForum: Broadcom SoC based Hardware   Posted: Wed Jul 05, 2023 4:29   Subject: Netgear wrt3500

All well and good, but now the admin sign in is lost and I have not been able to recover it. I cannot install an open vpn without that.


How did you manage to change the IP to 192.168.3.1 withou ...
  Topic: Hi
LOM

Replies: 7
Views: 730

PostForum: Broadcom SoC based Hardware   Posted: Wed Jul 05, 2023 4:20   Subject: Hi
Here is the Firmware: https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/07-01-2023-r53133/broadcom_K3X/dd-wrt.v24-53133_NEWD-2_K3.x_mega-WNR2000v2.chk

I doubt that file will fit in a 4MB F ...
  Topic: Need help installing dd-wrt for a ZTE MIFI
LOM

Replies: 10
Views: 1393

PostForum: General Questions   Posted: Fri Dec 09, 2022 5:37   Subject: Need help installing dd-wrt for a ZTE MIFI

What of the suggestion I made of editing the source code?

In order to do that you first need to have the complete source code for MF927u, something I don't think you have or will ever get because ...
  Topic: [SOLVED]Supported Alfa 4G USB dongle does not work
LOM

Replies: 11
Views: 1644

PostForum: Broadcom SoC based Hardware   Posted: Sun Jul 31, 2022 8:12   Subject: [SOLVED]Supported Alfa 4G USB dongle does not work
Are there any other possible solutions to make the setup more robust (not require manual setup)?

//Mattias

Yes, I have asked Brainslayer to flag all the Quectel cards I added support for as QMIR ...
  Topic: [SOLVED]Supported Alfa 4G USB dongle does not work
LOM

Replies: 11
Views: 1644

PostForum: Broadcom SoC based Hardware   Posted: Sun Jul 31, 2022 6:06   Subject: [SOLVED]Supported Alfa 4G USB dongle does not work

However, I get no WAN IP.
Any ideas?

//Mattias

It looks like the EC-25 uses raw_ip protocol.

See: https://forum.openwrt.org/t/openwrt-and-qmi-mode-lte-quectel-ec25-e-raw-ip/97680

Can y ...
  Topic: [SOLVED]Supported Alfa 4G USB dongle does not work
LOM

Replies: 11
Views: 1644

PostForum: Broadcom SoC based Hardware   Posted: Wed Jul 27, 2022 12:59   Subject: Re: Supported Alfa 4G USB dongle does not work
Hi there!

Any pointers on how to proceed would be very much appreciated - should I play around with usb_modeswitch? Even though depswa did have progress with usb_modeswitch I got the impression th ...
  Topic: Bootloader needed, again (buffalo wzr-1750dhp)
LOM

Replies: 26
Views: 4879

PostForum: Broadcom SoC based Hardware   Posted: Fri Jul 01, 2022 15:44   Subject: Bootloader needed, again (buffalo wzr-1750dhp)
and hereherehere(


No the CFE must not be 1024KB, it should be 512KB.
The uploaded CFE in your first link looks to be ok at a quick glance but it is duplicated (the second half has the same cont ...
  Topic: usb0 network interface
LOM

Replies: 8
Views: 3200

PostForum: Advanced Networking   Posted: Sun Apr 17, 2022 14:19   Subject: usb0 network interface
You need an ethernet over USB driver on the dd-wrt side, probably cdc_ether which is a kernel module and therefore has to be built at the same time as the kernel. It is normally not included in dd-wrt ...
  Topic: Webrevert file required for TL-WR841N v12
LOM

Replies: 8
Views: 2273

PostForum: Atheros WiSOC based Hardware   Posted: Tue Apr 05, 2022 6:23   Subject: Webrevert file required for TL-WR841N v12
I admit that on the actual specifics of what content is being checksum'd, I am ignorant as I have gone back and tried every way to run a checksum and still did not come up with the 4 bytes in your fil ...
  Topic: Webrevert file required for TL-WR841N v12
LOM

Replies: 8
Views: 2273

PostForum: Atheros WiSOC based Hardware   Posted: Tue Apr 05, 2022 3:25   Subject: Webrevert file required for TL-WR841N v12
It is the 1's complement of the CRC-32 digest over the area from 0x0c to the end of the file.
The value is 32-bit big endian stored in position 0x08 - 0x0b.

Since a TP-Link bootloader stripped fir ...
  Topic: Webrevert file required for TL-WR841N v12
LOM

Replies: 8
Views: 2273

PostForum: Atheros WiSOC based Hardware   Posted: Sat Apr 02, 2022 15:52   Subject: Webrevert file required for TL-WR841N v12
Well, it was not the header you should correct, it was the length of the original TP-Link firmware that was wrong.
You had lost the first byte in the stock firmware, (0x01) (and you obviously don't ...
  Topic: Webrevert file required for TL-WR841N v12
LOM

Replies: 8
Views: 2273

PostForum: Atheros WiSOC based Hardware   Posted: Mon Mar 14, 2022 6:04   Subject: Webrevert file required for TL-WR841N v12

WARNING: This file has not been tested, use at your own risk. It was created using the instructions above.

The file you have created is 0x3C001B bytes long but in your created header it says 0x3 ...
  Topic: Supported D-Link 4G USB dongle does not work
LOM

Replies: 13
Views: 3761

PostForum: Broadcom SoC based Hardware   Posted: Thu Feb 17, 2022 2:28   Subject: Supported D-Link 4G USB dongle does not work
After flashing a new build 48352, the modem worked right away and I have now ppp0 interface and internet functioning.

I think that is your problem, the modem is connecting using ppp serial dial-up ...
  Topic: Supported D-Link 4G USB dongle does not work
LOM

Replies: 13
Views: 3761

PostForum: Broadcom SoC based Hardware   Posted: Sun Feb 13, 2022 8:35   Subject: Supported D-Link 4G USB dongle does not work
The DWM-222 A2 is supported in an updated lib3g which will be included in future builds.

https://svn.dd-wrt.com/ticket/7534
  Topic: TP-LINK Archer C9 v.1 in bootloop/bricked after dd-wrt updat
LOM

Replies: 15
Views: 6211

PostForum: Broadcom SoC based Hardware   Posted: Tue Jan 18, 2022 13:02   Subject: TP-LINK Archer C9 v.1 in bootloop/bricked after dd-wrt updat
The same happened for me when flashing r48138.
I have sent a serial bootlog to Sebastian.
Goto page 1, 2, 3 ... 508, 509, 510  Next
All times are GMT
Navigation
Jump to: